[amass98]

Does anyone know where I can get a replacement trigger for my v2 Vapor? Mine is kinda screwed up and would like to get a new one.

[Mr. Charlie]

Try “The Other Athlete” or Ebay

[Quemiras]

Pooty had some

[chanceb23]

So when I air up my Vapor the bolt shoots forward and leaks down the barrel? Any info would help

[digital sol]

Anybody have any aftermarket parts?

I picked up a 2014 Vapor and was looking for trigger or bolt replacement options.

Thanks!

[the korean1]

Originally Posted by digital sol

Anybody have any aftermarket parts?

I picked up a 2014 Vapor and was looking for trigger or bolt replacement options.

Thanks!

there are none for the bolt. the trigger can be I think replaced with a shocker nxt trig. but I've never confirmed it.

[digital sol]

Originally Posted by the korean1

there are none for the bolt. the trigger can be I think replaced with a shocker nxt trig. but I've never confirmed it.

Thanks!

[p8ntballer101]

Just to keep this thread up there-
machinepaintball.com is up and running again, as of this post, they have spare parts for 2012, 2014 and the newest machine marker to hit the market.

[TyphoonX]

I have a 2012, recent pickup, screen is dead and I have a 09 Ego board I’m going to throw in it. What are the stock board settings?

[p8ntballer101]

this told me everything i needed to know-
https://www.pbnation.com/showthread.php?t=3828358

[TyphoonX]

Originally Posted by p8ntballer101

this told me everything i needed to know-
https://www.pbnation.com/showthread.php?t=3828358

That’s a great guide for tuning and troubleshooting. I’m looking for stock settings so I can tune from there and am too lazy to read 61 pages in hopes I’d find them From what I’ve ready the Virtue and Ape menus are different. Worst case scenario I’ll have to see how well his setting transfer to my setup.

[jromez#18]

Following this

[y0ukn0wit]

Hi - so I recently acquired what I think is a V2 Vapor from a PB buddy as payment for teching all his guns the past two season. I'm new to this platform. I got the marker cleaned up and lubed. The only issue I'm having is that the OLED screen is dark (no display) but the board turns on and the gun is shooting just fine. Anyone know if buying a new OLED screen solves the issue?

Also, if I decide to sell the marker does anyone know what the market value for these are? This is is in pretty good cosmetic shape I'd say 90/100. According to my friend it was used only a few times and then sat on a wall as a display item for years so very low "mileage"

Thanks in advance for any info

[Paul77]

Originally Posted by y0ukn0wit

Hi - so I recently acquired what I think is a V2 Vapor from a PB buddy as payment for teching all his guns the past two season. I'm new to this platform. I got the marker cleaned up and lubed. The only issue I'm having is that the OLED screen is dark (no display) but the board turns on and the gun is shooting just fine. Anyone know if buying a new OLED screen solves the issue?

Also, if I decide to sell the marker does anyone know what the market value for these are? This is is in pretty good cosmetic shape I'd say 90/100. According to my friend it was used only a few times and then sat on a wall as a display item for years so very low "mileage"

Thanks in advance for any info

It uses a ego 9 board, the stock oled’s are garbage imo. Good luck on trying to find a Led/oled virtue board. That’s the way to fix it.

[Mex1515]

i just got a 2012 vapor, and im looking for some parts do you guys know were i can get some extra ball detentes as well as a extra set of eyes?

thank you!

[Paul77]

Originally Posted by Mex1515

i just got a 2012 vapor, and im looking for some parts do you guys know were i can get some extra ball detentes as well as a extra set of eyes?

thank you!

id contact machine, you may be SOL on the 2012, they shot a liitle better than the 2014 but parts were an issue from day one.

Machine Paintball
Service Center
6300 Grelot RD, Ste G114
Mobile, AL 36609
Call us at 251-214-0399

[Mex1515]

Originally Posted by Paul77

id contact machine, you may be SOL on the 2012, they shot a liitle better than the 2014 but parts were an issue from day one.

Machine Paintball
Service Center
6300 Grelot RD, Ste G114
Mobile, AL 36609
Call us at 251-214-0399

Got it thank you!!

[aresfiend]

I'm in a really weird spot with one of my 2012 Vapors. The air is inconsistently pushing the bolt forward and the solenoid is leaking somewhere in the actuator assembly.

Long story short, if I swap every functional part (bolt engine, reg, noid) from one known good Vapor onto this body the bolt will eventually slide forward with the solenoid leaking from the get go. If I swap every functional part originally from this gun into the other Vapor it works in the other body.

I have rebuilt the entire bolt engine, the reg, and serviced the solenoid. I know it's not leaking at the frame to body seal, all of the body side ports for the reg are fine as well as the HPR bonnet so I doubt it's just blasting HP air past the reg. The body side mating surface is at least flat to 0.005" (my 0.002 feeler is damaged so I didn't check that). Both solenoid gaskets are fine and seal to the other body with no problem. Is there something I'm missing?

[Pizzimp]

Originally Posted by aresfiend

I'm in a really weird spot with one of my 2012 Vapors. The air is inconsistently pushing the bolt forward and the solenoid is leaking somewhere in the actuator assembly.

Long story short, if I swap every functional part (bolt engine, reg, noid) from one known good Vapor onto this body the bolt will eventually slide forward with the solenoid leaking from the get go. If I swap every functional part originally from this gun into the other Vapor it works in the other body.

I have rebuilt the entire bolt engine, the reg, and serviced the solenoid. I know it's not leaking at the frame to body seal, all of the body side ports for the reg are fine as well as the HPR bonnet so I doubt it's just blasting HP air past the reg. The body side mating surface is at least flat to 0.005" (my 0.002 feeler is damaged so I didn't check that). Both solenoid gaskets are fine and seal to the other body with no problem. Is there something I'm missing?

I recently went through a struggle with my 2012 as well. It was the first vapor I owned and gave me fits. I’ll list out my issues and maybe they will help you.

Whenever I would air up the gun it would automatically start cycling like it was in full auto until you would pull the trigger once then would pressurize as normal. What fixed this was replacing the two 013 o rings on the bolt stem.

The next issue was the gun constantly having a steady leak from the vent hole. I broke down solenoid and cleaned and greased it. The seals and rings looked fine but yet it still leaked. I suspected that maybe the noid wasn’t fully closing so I broker it all down again and stretched the spring that’s on the piston maybe 1/16th to 1/8th inch. That fixed the vent leak.

Then I had a very slight leak in the feed neck. I replaced both body rings and still the leak persisted.

The final fix was replacing the 017 rings in the bolt can with 018 rings and that fixed all my leaks.

Hopefully that helps. These damn things are needy but I love mine.

[aresfiend]

I just want to touch back on this, I figured it out a few weeks ago but forgot I made a post here.

I had a crack in the body between two of the air channels between the solenoid and the bolt assembly.

[Mr. Charlie]

^Thats pretty crazy!

How did you ever figure that out? It probably took forever chasing leaks or inefficiency?

I bet it happened during manufacturing and they still tried to make it a complete marker...

Haven’t been hearing much at all about the 2019 Vapor. Maybe that’s a good thing? ��