[foreverpsycotic]

What is the efficiency of it?

[Apocalyptic]

That is hugely impressive. I would love to get mine done it's been sitting in parts probably 60% done and it's hurting my feelings leaving it sitting around here... I'm never going to have the proper equipment to finish it properly...

Good job... You hopefully have inspired me to finish mine!!!

[cfos00]

If you're having trouble with putting the puppy together, let me know. I ran into about every problem you can putting this one together and managed to get through them, so I might be able to point you in the right direction.

[FoidPoosening]

stay with the uprising frame.

Oh, and throw a 13/3000 ninja tank on that beast and itll be so light, it might just float out of your hands.

Nice work! Vid please

[cfos00]

A few slight changes that have made a monsterous difference.






I put a critical trigger and switch in, put a MP4 ram on it, and an Outkast lpr on it. It cycles more smoothly, and can be walked now. It also looks a whole lot better with the new trigger in my opinion. Running well at a little over 420psi.

[Darkapollo]

that is freakin sweet.

[Codymm1014]

You have inspired me.

[tipp98chopshop]

Only one thing could explain my opinion on this gun...

[Saucy27]

weight? videos?

your leaving us hanging man it looks so sexy in pictures we need videos

[lsongj721]

If you could ever bear to pay for more work...I wonder if its possible to mod for an MQ valve...

Put an eclipse frame, tadao yakuze, E2 solenoid cover, and an MQ2. Basically you would have a cocker in a pgp.

Lol

[tooks]

A video PLEASE!!!!!!!- It think i speak for everyone when I say we need to see this ripping!

[wowzerz]

lol at the 1/4" macro

[The Inflicted]

The match-anodized pump arm and frame adapter rail are what make this one for me.
What an awesome project gun!

[cfos00]

I may see about doing a really fast video next time I hit the fields.

Yeah, the tiny piece of macro is a bit goofy, but I like it.

The MQ thing would be incredibly hard to pull off. The diameter of the lower tube is a lot bigger than a cockers. You'd have to get the spacing right, make spacers for the MQ, and get it all sealed up. The spacers are the tricky part. Or you could cut off the lower tube, and solder on a new, smaller lower tube. If anyone can do it and pull it off, kudos but not really what I was going for with this one. I still like my little sear tripper here.

[Crimsonkid]

I've had this design in mind before, except mine would have an MQ2 valve so it would be incredibly short

[surfbum]

this thing is awesome!
i've wanted to do a pgp/cocker mod for a while, but never got around to it
great work!

[cfos00]

Not sure a mq valve would actually shorten it. The mq's aren't really small and the pgp set up in the lower tube is significantly shorter than a cocker (which is why they can be really hard to time). Once you add on the frontblock for the air chamber to have enough volume, I'm honestly not sure you'd save much. Plus if you want the gun to have a chance at getting to velocity and have a semblance of efficiency you can't cut the the barrel down too much. And that doesn't address the diameter problem of the lower tube. Not saying it can't be done because anyone with the time/skill/motivation/$ could do it, but it would be a challenge to say the least (that said, it would be pretty freaking sweet and would probably save a lot of timing headaches). I've seen a couple e-bladed out there and they look awesome.

As you may have guessed, the MQ thought did run through my mind more than once.

[shawndorts]

you get 10 points sir

[not CrunchyMilk]

Very impressive sir. I personally can't play with a drop, especially one that extreme but it accomplishes the goal of a a tiny footprint.

[cfos00]

See I have the opposite issue---can't shoot a gun without one on it. I've played with one for over a decade now, and it really messes with me there isn't one there.

[killteamTRS]

thats sick