Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 09-24-2012, 06:44 PM #1
Archhh
 
 
Join Date: Aug 2012
How do you adjust the Rate of Fire on the vision board of the nxt?

I have the vision board for the NXT, and it did not come with a manual.
I know there is a manual online which is located @

http://www.claymorepaintball.com/Fil...hocker_NXT.pdf

,but i did not see a section about adjusting the rate of fire. I think it's talking about old board that came with the original shocker.

PS: is a trigger a good upgrade for this gun?
Archhh is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 09-24-2012, 07:17 PM #2
rolo223
 
 
rolo223's Avatar
 
Join Date: Sep 2006
Location: KC
try zdspb.com. here's a link.

http://www.zdspb.com/tech/mguide/sho...cs_nrvnxt.html

the stock nxt board is the "nerve" board, explained on the page in the link.

ya, a trigger is one of the few upgrades the gun really needs. i prefer critical triggers. you should also look into a rhino spring and spring modded bolt.
rolo223 is offline   Reply With Quote
Old 09-24-2012, 08:16 PM #3
Archhh
 
 
Join Date: Aug 2012
I'm still having issues. Does anyone have any information about shocker vision board?
Archhh is offline   Reply With Quote
Old 09-24-2012, 08:20 PM #4
Archhh
 
 
Join Date: Aug 2012
I have the same board as mike


Last edited by Archhh : 09-24-2012 at 08:29 PM.
Archhh is offline   Reply With Quote
Old 09-24-2012, 08:37 PM #5
rolo223
 
 
rolo223's Avatar
 
Join Date: Sep 2006
Location: KC
thats the nerve board. as far as i know all that changed with the 2009 version was the rebound (aka ramping) modes were set for psp, millenium, etc (3 shot, etc). the pre 09 rebound settings were just how fast you had to pull to activate standard ramping.

regardless of which style of ramping you activate (psp, millenium, etc) on the nerve board you set the rate of fire using the recharge rate and the dwell. use the chart on the link i listed before, or the formula is at the bottom of it.

example:

12.5 bps=27 to 30 dwell chirps+55 recharge chirps

a chirp is 1/4 millisecond, so 30 chirps is 10.5ms (3ms start + 7.5ms setting)

Last edited by rolo223 : 09-24-2012 at 08:50 PM.
rolo223 is offline   Reply With Quote
Old 09-24-2012, 08:47 PM #6
Archhh
 
 
Join Date: Aug 2012
Alright. Can you guide me, so I can make my gun shoot at least 17-20 bps or more?
Archhh is offline   Reply With Quote
Old 09-24-2012, 08:53 PM #7
rolo223
 
 
rolo223's Avatar
 
Join Date: Sep 2006
Location: KC
about halfway down the page on zds..

If you wish your marker to fire the maximum speed, simply set the recharge setting to 0 chirps.
rolo223 is offline   Reply With Quote
Old 09-25-2012, 05:42 AM #8
Archhh
 
 
Join Date: Aug 2012
sweet! My dwell chirp is at its maximum, so all i have to do is decrease the recharge rate to zero to make it shoot its maximum bps?
Archhh is offline   Reply With Quote
Old 09-25-2012, 07:31 AM #9
rolo223
 
 
rolo223's Avatar
 
Join Date: Sep 2006
Location: KC
ya put your recharge to zero, but since all you're looking for is max bps, you should also set your dwell to the lowest dwell where the gun will still cycle. here's another link to a different page on zdspb that details it. http://www.zdspb.com/tech/mguide/sho...ectronics.html

and this is the how to do it part:
(with the gun aired up...)
1. Lower the dwell to the minimum setting (or an extremely low setting, such as 12 chirps or 6 milliseconds).
2. Gradually increase dwell until the marker begins to fully cycle. You will know this time because, when the marker has trouble cycling, the sound of the bolt firing will be muffled and sound erratic, denoting inconsistencies. When you reach the point where it fully cycles, the marker will sound loud on each shot fired, with minimal sound difference between the shots (inconsistencies can be caused by other things, such as the reg, please note).
3. Once the Shocker is fully cycling, increase the dwell another 8-12 chirps (2-3 milliseconds), and that will be your dwell setting.

a good starting point for the lowest dwell is around 11-12 milliseconds (35 chirps) unless you have a sprung/aftermarket bolt kit

Last edited by rolo223 : 09-25-2012 at 07:39 AM.
rolo223 is offline   Reply With Quote
Old 09-25-2012, 04:14 PM #10
Archhh
 
 
Join Date: Aug 2012
lol wow i feel like an idiot now for not knowing this. Thanks!
Archhh is offline   Reply With Quote
Old 09-25-2012, 06:00 PM #11
rolo223
 
 
rolo223's Avatar
 
Join Date: Sep 2006
Location: KC
np. the stock board is good, but it can be a pain to work with without a detailed manual ;p zdspb is a must! nice to see its working ok in your vid lol
rolo223 is offline   Reply With Quote
Old 09-25-2012, 06:36 PM #12
holson72
 
 
holson72's Avatar
 
Join Date: Jan 2008
Location: Lubbock, TX
holson72 posts videos on PbNation
holson72 has achieved Level 1 in PbNation Pursuit
FWIW, my dwell with a stock bolt was 14 ms.
__________________
My Collection
holson72 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump