*grumbles about his TES problem* - PbNation
Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

 
Archived Thread - Cannot Edit  
Old 02-20-2005, 12:08 PM #1
Rare Faction
The Cap'n
 
Rare Faction's Avatar
 
Join Date: Jan 2004
Location: 614
 has been a member for 10 years
*grumbles about his TES problem*

Well, not really my problem, but my little brother whines a bunch, so here I am

He's got a TES with a Scion 68/5k on-gun tank and gas-through grip, Boomstick, everything else is stock. When we air up the gun, if it's not cocked sometimes we can hear it leaking down the barrel. When trying to fire (set in Semi 4 with a 5ms dwell), the bolt doesn't seem to catch the sear every time; sometimes it will bounce back a couple times, sometimes it will 1/2 cock itself. Worst of all, it'll end up chopping a few balls

Anyone got any suggestions?

Thanks!
__________________
Moar plundar!
Rare Faction is offline  
Old Sponsored Links Remove Advertisement
Advertisement
Old 02-20-2005, 12:14 PM #2
GooG
Formally KnownAs MiniGooG
 
GooG's Avatar
 
Join Date: Feb 2005
definitly need a new cup seal, and once you fix that worry about the chopping
GooG is offline  
Old 02-20-2005, 12:16 PM #3
look>there>i>am
 
 
look>there>i>am's Avatar
 
Join Date: Jan 2005
Location: tx
yyeh
1 jam bolt for chops
2 that must be one heavy tank
3 cock the gun befor you puty air on it
4 get a magnetic triga for bounces
__________________
you may be able to shot 15+ but it only takes one to get someone out
|^^^^^^^^^^^^^^||*
|-----im rich *****----|| '|";\___
|_..._..._______===|=||_|__|...,]
"(@)'(@)""""''' |(@ )(@ ) ````(@)i wish
look>there>i>am is offline  
Old 02-20-2005, 12:17 PM #4
Waam
Banned
 
Join Date: Jul 2004
Location: Cali
Ok well first off Tes's dont use the dwell and all that if im correct. Next try cocking the gun before u air it up, then also the decocking problem is going to happen, he needs a new bolt to solve that problem. I had the same problems so no worries to him.
Waam is offline  
Old 02-20-2005, 12:19 PM #5
AdrenalineRush
 
 
AdrenalineRush's Avatar
 
Join Date: Nov 2003
Location: Minnesota
AdrenalineRush is a Supporting Member
 has been a member for 10 years
http://www.pbnation.com/showthread.p...hreadid=439514
__________________

My Feedback

AdrenalineRush is offline  
Old 02-20-2005, 12:36 PM #6
Rare Faction
The Cap'n
 
Rare Faction's Avatar
 
Join Date: Jan 2004
Location: 614
 has been a member for 10 years
If the gun is cocked before airing it up, there's still a very faint hiss down the barrel

Looks like I'll have to get him to invest in a new bolt and a replacement cup seal...I'll let ya'all know how it turns out
__________________
Moar plundar!
Rare Faction is offline  
Old 02-20-2005, 12:43 PM #7
AdrenalineRush
 
 
AdrenalineRush's Avatar
 
Join Date: Nov 2003
Location: Minnesota
AdrenalineRush is a Supporting Member
 has been a member for 10 years
Did you read that thread? If your firing and the bolt is not catching it could be burping. Which means you want to sand down the plunger on the noid till its flat not beveled.
__________________

My Feedback

AdrenalineRush is offline  
Old 02-20-2005, 01:19 PM #8
Rare Faction
The Cap'n
 
Rare Faction's Avatar
 
Join Date: Jan 2004
Location: 614
 has been a member for 10 years
Well, I took the front block off, and lo and behold, he's missing the cup seal star. I have no idea how it's gone missing, as he's only 13 and has never opened the thing up before. Would this be the cause of the leaking down the barrel?

AR- is there a way to tell if I need to sand or not? Would it cause any ill effects if that's not the cause?
__________________
Moar plundar!
Rare Faction is offline  
Old 02-20-2005, 04:33 PM #9
balla893
*Insert witty statement*
 
balla893's Avatar
 
Join Date: Jan 2004
Location: California
 has been a member for 10 years
The TES's don't come with the cup seal stars. It's in the manual but they don't actually have them.
__________________
Feedback
balla893 is offline  
Old 02-20-2005, 05:18 PM #10
Pho-King Peter
PISTAL PETE
 
Pho-King Peter's Avatar
 
Join Date: Oct 2004
Location: Westminsta-HB, CA
they dont need the stars since the spring is a cone shape. Put paper from hole puncher, under the spring for the spring to hold the sear harder for buring problem. Telfon under the o rings in the va for the leaking problem. i had the same it worked or teflon on the screw that holds the va
__________________
Legacy fan #183
FEEDbAK ^_^
Pho-King Peter is offline  
Old 02-20-2005, 05:19 PM #11
AdrenalineRush
 
 
AdrenalineRush's Avatar
 
Join Date: Nov 2003
Location: Minnesota
AdrenalineRush is a Supporting Member
 has been a member for 10 years
Did some searching for you.

http://www.pbnation.com/showthread.p...hreadid=623856
__________________

My Feedback

AdrenalineRush is offline  
Old 02-20-2005, 05:38 PM #12
Rare Faction
The Cap'n
 
Rare Faction's Avatar
 
Join Date: Jan 2004
Location: 614
 has been a member for 10 years
Ooo, thanks for all the info

*gets to it*
__________________
Moar plundar!
Rare Faction is offline  
Old 02-20-2005, 07:13 PM #13
tombstone
 
 
tombstone's Avatar
 
Join Date: Nov 2004
Location: top secret
tombstone is a Supporting Member
First off do not sand anything shortening the noid shaft will make burping worse because in effect you are reducing the height of the sear.Try strectching the sear spring a little.That marker should have reg and not a gas through grip.Set the pressure up to 350 psi and see how it works.You should not need a new bolt if you need anything it would be a striker becuse that is what locks up with sear not the bolt.Clean it and lube it and set the pressure ,then see how it works.
__________________
FEEDBACK
tombstone is offline  
Old 02-20-2005, 07:36 PM #14
half-step
 
 
half-step's Avatar
 
Join Date: Jun 2004
Location: WI
half-step is a Supporting Member
 has been a member for 10 years
Shortening the noid shaft will not reduce the sear height. It will back the shaft away from the sear some and actually allow the sear to sit higher. But shortening it too much will not allow the noid to trip the sear. Shortening the noid shaft is one of the ways to correct the burping issue. Only shorten the shaft to the tapered part.
__________________
Red-Black T1 * Palmer Stablizer & Micro-Rock * CP Rail w/On-Off * Eclipse QEV * ACP Blue Bolt w/X-rings * OGI Speedneck * J&J 2-Piece 14" Barrel * Egg w/Z-Board * Rocket Valve * ACPB Delrin Ram

Grey TES * CP Reg * Bullet Drop w/On-Off * Bandit Bolt * 50g Switch * 3 Point Stock Trigger Mod * Rocket Valve * Clamp Feedneck * JAVA Recharge Mod

Dragun Mods*Manuals
My Feedback
half-step is offline  
Old 02-20-2005, 10:37 PM #15
tombstone
 
 
tombstone's Avatar
 
Join Date: Nov 2004
Location: top secret
tombstone is a Supporting Member
Well I stand corrected half step is right after looking at the noid.Use that as a last resort though.Also you may want to change your striker oring replace it with a spyder striker oring they are a clear-red color.That is the cause of a lot of burps with the spyders.
__________________
FEEDBACK
tombstone is offline  
Old 02-21-2005, 11:00 AM #16
redd_neck
 
 
redd_neck's Avatar
 
Join Date: Feb 2004
Location: Carolina panther country
 has been a member for 10 years
Quote:
Originally posted by tombstone
Well I stand corrected half step is right after looking at the noid.Use that as a last resort though.Also you may want to change your striker oring replace it with a spyder striker oring they are a clear-red color.That is the cause of a lot of burps with the spyders.

I don't know about your striker but mine doesn't have a o-ring it just has a plastic suction cap thing on it.
__________________
Mini- Freak kit
OutKast- BL torpedo, Freak kit, cp on/off
redd_neck is offline  
 




Posting Rules
Forum Jump