[Evil Rocky]

Any reg. I own a AKA 2liter and ST/CP reg.

On one PIMP I use my AKA and my EFT I use my detenator. I am upset that I bought a ST/CP reg becaue the detenator is so much better on consistancy.

But if looking to make changes on weight jusat change the booth regs and that will save a lot. My AKA is heavier than my detenator.

[adevil]

First off I'll apologize if I've missed it, but I have looked through the threads, FAQs and stickies and haven't seen my problem.

My Pimp with Ghetto board with randomly fire off 3 balls with one pull of the trigger, it happens with eyes on or off. It happens with tourney lock on, or tourney lock off and adjusting down the ROF and ETS.

Any suggestions? Thanks in advance.

[Evil Rocky]

Your ETS might be to low and your tigg to close as well for teh bounce. Are you ramping or semi? Ramping will shoot that many balls sometimes with that trigg pull ona low ets

[adevil]

some how i missed the Firing Mode portion of the sheet for the board settings, i'm an idiot

[wyckofflax16 (Banned)]

I just ordered an upped pimp with a was board can some one pm me explaining how to use it?

[wyckofflax16 (Banned)]

I just ordered an upped pimp with a was board can some one pm me explaining how to use it?

[Evil Rocky]

wickedairsports.com and go to manuals and see the manual that way.

Thanks

[wyckofflax16 (Banned)]

nvr i also have the ramping board 7.0. and i was wondering if any one can tell me how to change the modes

[tips_000]

u should make an upgrades thread on any ups u can get and were 2 get them

[shspaintballer09]

can someone post the instruction manuel for the pimp kit 7.0 ghetto board

[EvilPimp_]

Originally Posted by shspaintballer09

can someone post the instruction manuel for the pimp kit 7.0 ghetto board

It's in the Pimp FAQ.....

see page 2

[jrod1321]

one of the wires on my 9v connector came off...will evil send me a new wire harness for free?

[paintballn]

hey can some 1 tell me what the stock pimps firing modes are

[wolfman99]

Hey everone. I had problems with my eyes early on simply from use. I purchased brand new eyes and yet even with a liscensed technician, I can't seem to get them to work. The pimp L.E.D. light still cycles orange then red, which indicates that there is no ball in the chamber, despite when there is one in the chamber. Can anyone help me install and know how to work the eyes properly after installation.

[wolfman99]

Hello everyone. I have been having problems with the eyes in the Pimp Kit since the beginning of use. I had a technician install new ones however, the L.E.D. light still cycles orange then red which means there is no ball in the chamber even though there clearly is. If someone could get back to me on the proper installation or any additional information that I need to know after installation that would be great thanks. And sorry for the second post

Matt

[bballryand316]

Make sure the eyes are aligned, make sure they are clean, and make ure the eye wire is properly connected to the board.

Also, regardless of how it sounds, try a new fresh battery.

[haywoodjublomi]

If you put your finger in the chamber does it register? If so you might need to adjust your ram.

[Paintballnskills]

is 300 a good price for a pimp halo and steely tank

[BeenPimpSlapped?]

About average. Figure $150 for a used PIMP. $50 for the Halo. $50 for the Tank. Since you can get a good used Fiber wrapped HPA for $65-$85, I'd hold off on the steely tank.

[bballryand316]

I'd say it's a little high.

[deke3]

ok i have a evil pimp but the back of the bolt brok and i cant get it out dose any one know how to take it out....