Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 03-20-2014, 08:36 PM #1
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
Need Help****

I just picked up a revi from my friend and he said that it needed a new reg seat. i got a new one and replaced it and know the gun doesnt shoot. It airs up but doesnt shoot.
TresPaintball is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 03-20-2014, 08:41 PM #2
firefoxx04
Up the Irons
 
firefoxx04's Avatar
 
Join Date: Jul 2008
Location: Michigan
firefoxx04 supports Bob Gurnsey
firefoxx04 supports DLX Technology
is the adjustment screw turned all the way in (clockwise)?

If, make sure it was not turned so far in that it damaged the new reg seat. Being turned too far in is what damages reg seats in the first place.

You might want to double check the reg seat and use a fresh battery.


With the gun aired up, turn it on with eyes off. Start dry firing and slowly turn the reg screw counter clockwise until the gun shoots. It might leak slightly for a moment, seal, puff and then shoot in that order.

If you have a pressure gauge, check to make sure their is pressure. Set the pressure to at least 150 but no more than 200psi. With the gun cycling and pressure set, use a crono to dial into your fps.
firefoxx04 is offline   Reply With Quote
Old 03-20-2014, 08:56 PM #3
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
Quote:
Originally Posted by firefoxx04 View Post
is the adjustment screw turned all the way in (clockwise)?

If, make sure it was not turned so far in that it damaged the new reg seat. Being turned too far in is what damages reg seats in the first place.

You might want to double check the reg seat and use a fresh battery.


With the gun aired up, turn it on with eyes off. Start dry firing and slowly turn the reg screw counter clockwise until the gun shoots. It might leak slightly for a moment, seal, puff and then shoot in that order.

If you have a pressure gauge, check to make sure their is pressure. Set the pressure to at least 150 but no more than 200psi. With the gun cycling and pressure set, use a crono to dial into your fps.
which one is the adjusment screw?
lol srry but thank you
TresPaintball is offline   Reply With Quote
Old 03-20-2014, 09:02 PM #4
firefoxx04
Up the Irons
 
firefoxx04's Avatar
 
Join Date: Jul 2008
Location: Michigan
firefoxx04 supports Bob Gurnsey
firefoxx04 supports DLX Technology
it should be the only screw on the reg. There might be a second small screw that lets you adjust the macro fittings position.

You want the 1/4inch screw at the bottom of the reg. Check to see if its all the way in but DONT over tighten it clockwise.
firefoxx04 is offline   Reply With Quote
Old 03-20-2014, 09:30 PM #5
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
Quote:
Originally Posted by firefoxx04 View Post
it should be the only screw on the reg. There might be a second small screw that lets you adjust the macro fittings position.

You want the 1/4inch screw at the bottom of the reg. Check to see if its all the way in but DONT over tighten it clockwise.
yes its alll they way in, but the donut that hold's it in isn't touching it.

Last edited by TresPaintball : 03-20-2014 at 09:46 PM.
TresPaintball is offline   Reply With Quote
Old 03-20-2014, 09:53 PM #6
firefoxx04
Up the Irons
 
firefoxx04's Avatar
 
Join Date: Jul 2008
Location: Michigan
firefoxx04 supports Bob Gurnsey
firefoxx04 supports DLX Technology
Donut?

If the screw is all the way in then its set to 0psi. If its cranked down pretty good youl want to back it out a good full turn. Id open the reg up again and check to see if the seat has been crushed.
firefoxx04 is offline   Reply With Quote
Old 03-20-2014, 11:07 PM #7
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
On the revi their is a donut that hold the reg seat in .
TresPaintball is offline   Reply With Quote
Old 03-20-2014, 11:14 PM #8
GraniteGargoyle
 
 
GraniteGargoyle's Avatar
 
Join Date: Oct 2011
GraniteGargoyle is attending Decay of Nations VI
GraniteGargoyle supports Empire
The C clip I am guessing he is talking about.
__________________
Need Paintball Stuff? Talk To Yeti6669
GraniteGargoyle is offline   Reply With Quote
Old 03-21-2014, 12:03 AM #9
8765
 
 
8765's Avatar
 
Join Date: Oct 2011
The reg seat shouldn't touch the c-clip, although it may come very close to. If the seat is turned out to the point where its pressed up against the c-clip, the reg is at max output pressure, and that's very bad for the marker.
__________________
"Memory is cheap." -Dr. Sam Kassegne
8765 is offline   Reply With Quote
Old 03-21-2014, 12:10 AM #10
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
ok, i just have it turnuned in all the way like the guy before said
TresPaintball is offline   Reply With Quote
Old 03-21-2014, 09:50 AM #11
Dedloc
That guy.
 
Dedloc's Avatar
 
Join Date: Sep 2010
Location: Tennessee
Annual Supporting Member
Dedloc is BST Legit
Dedloc is reppin' sidebar 4 life
Dedloc is Legendary
Ok, turn the screw in clockwise until it stops. DO NOT OVERTIGHTEN. Air the marker up and SLOWLY turn the reg screw counter-clockwise until the marker begins to fire.
__________________
Sic gorgiamus allos subjectatos nunc.
PARADOX

Last edited by Dedloc : 03-21-2014 at 11:58 AM.
Dedloc is offline   Reply With Quote
Old 03-21-2014, 11:56 AM #12
TresPaintball
 
 
TresPaintball's Avatar
 
Join Date: Jan 2014
ok i will thank you
TresPaintball is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump