Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 02-24-2013, 09:05 PM #1
mattbrace
Dr. Isotope
 
mattbrace's Avatar
 
Join Date: Dec 2011
Location: So Cal
G3 Issue

As my sig says I have a G3 with the TechT, I recently purchased it broken from a fella on here since I have had the marker before I am working on fixing it, I have thoroughly cleaned and lubed the entire gun. I have the stock reg and have tried to use the gun with it, there is no leaks and the gun cycles fine but does not get to full velocity and when it fires the ball just rolls out of the barrel.

The velocity is set to the highest setting as well. I have a fresh battery installed just to be sure the noid was getting full power. I am using the Virtue Redefined OLED board just minus the OLED.

I also have a CP reg that causes the gun to cycle but when I back the screw out too far the noids click disappears and the gun no longer cycles. I am using a LP Ninja reg that is currently set to roughly Low 500 PSI output pressure, not sure if this is even related.

Wondering what you all though it might be...thanks.
__________________
Dr. Isotope
mattbrace is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 02-24-2013, 09:11 PM #2
firefoxx04
Up the Irons
 
firefoxx04's Avatar
 
Join Date: Jul 2008
Location: Michigan
firefoxx04 supports Bob Gurnsey
firefoxx04 supports DLX Technology
did you check the dwell? virtue does it in .5ms increments. The manual might say otherwise but its a typo.

try 14ms (28blinks)

did you relube the noid?


try your cp reg at 0psi, and turn it out until the gun starts to cycle.. turning it to far will overpressurize the noid and cause it to lock up until you depressurize the gun.
firefoxx04 is offline   Reply With Quote
Old 02-24-2013, 09:16 PM #3
GraniteGargoyle
 
 
GraniteGargoyle's Avatar
 
Join Date: Oct 2011
GraniteGargoyle is attending Decay of Nations VI
GraniteGargoyle supports Empire
Quote:
Originally Posted by firefoxx04 View Post
did you check the dwell? virtue does it in .5ms increments. The manual might say otherwise but its a typo.

try 14ms (28blinks)

did you relube the noid?


try your cp reg at 0psi, and turn it out until the gun starts to cycle.. turning it to far will overpressurize the noid and cause it to lock up until you depressurize the gun.
This
__________________
Need Paintball Stuff? Talk To Yeti6669
GraniteGargoyle is offline   Reply With Quote
Old 02-24-2013, 09:32 PM #4
mattbrace
Dr. Isotope
 
mattbrace's Avatar
 
Join Date: Dec 2011
Location: So Cal
Lol that was it. Shocked. My dwell was too low. Thanks for the tip!
__________________
Dr. Isotope
mattbrace is offline   Reply With Quote
Old 02-24-2013, 09:38 PM #5
firefoxx04
Up the Irons
 
firefoxx04's Avatar
 
Join Date: Jul 2008
Location: Michigan
firefoxx04 supports Bob Gurnsey
firefoxx04 supports DLX Technology
not the first time this has happened!

I have a virtued f7.. could not get it to crono for the life of me, even at 300psi. dwell was 3ms when it should have been 6-8!
firefoxx04 is offline   Reply With Quote
Old 02-24-2013, 09:39 PM #6
mattbrace
Dr. Isotope
 
mattbrace's Avatar
 
Join Date: Dec 2011
Location: So Cal
Quote:
Originally Posted by firefoxx04 View Post
not the first time this has happened!

I have a virtued f7.. could not get it to crono for the life of me, even at 300psi. dwell was 3ms when it should have been 6-8!
Ya that's crazy mentions it no where in the manual they are half ms increments. Thanks again!!
__________________
Dr. Isotope
mattbrace is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump