[Tapok]

Ok guys, so I have recently bought a G6R 12 from ANS. I love the gun, however, I have a problem which make me not love it as much.

My problem is that its eyes are "slow". I don't really know what to call this issue, however, if I stick my finger inside the breach it take a second or more for the eyes to recognize it and show it on the screen. I have asked a few people who have the same gun and they said that they have never had such an issue. What do I do? This causes my g6r to chop balls like crazy. It very annoying anyone has a solution or the same problem?

Thanks!

[cire83]

2c or 4c eyes? Where is the eye delay set on the board?

[Tapok]

Originally Posted by cire83

2c or 4c eyes?

2c eyes. its all stock

[gamer565]

Could just be the OLED delaying the display.

What are all your settings at? Don't say stock, list them.

[cire83]

hmm.... nothing partially blocking an eye?

[Tapok]

Originally Posted by gamer565

Could just be the OLED delaying the display.

What are all your settings at? Don't say stock, list them.

but im choping like a mother******
my settings are (frenzy 5.0)
1. semi
2. rof cap 15
3. timer 10 (idk why u need to know this but i still listed lol)
4. debounce 02mS
5. Mech debounce 03
6. trigger filter 06
7.dwell 06.0mS
8. 68 caliber
9.bolt delay 15mS

[Tapok]

Originally Posted by cire83

hmm.... nothing partially blocking an eye?

cleaned it all
and they work, it just takes them a sec to do so

[cire83]

thats the exact same setting that mine is set at N have hardly ever chopped a single ball.
U have pressure tester? are your pressures set properly?

Make sure the eyes a installed correctly.

Also Is this a custom ansgear.com anno?

[Tapok]

Originally Posted by cire83

thats the exact same setting that mine is set at N have hardly ever chopped a single ball.
U have pressure tester? are your pressures set properly?

Make sure the eyes a installed correctly.

Also Is this a custom ansgear.com anno?

Yes i do and i always pressure test my g6r to the correct pressures before and after playing
i lube and stuff like that properly too (lol)
they seem to be installed correctly as the pro tech guy found no issue
yes it is a custom

[cire83]

most likely a faulty eye......

[HeadHunter59]

Make sure plugs are interested all the way on eyes and board.

Id take them out and look to see if eyes(board) got cracked. With that make sure you don't over tighten the screws that hold the eyes in place.

[Tapok]

Originally Posted by cire83

most likely a faulty eye......

Originally Posted by HeadHunter59

Make sure plugs are interested all the way on eyes and board.

Id take them out and look to see if eyes(board) got cracked. With that make sure you don't over tighten the screws that hold the eyes in place.

Actually guy what I just did was take a ball, drop it in, and shoot. The gun shoots right away but the screen does not show that the eyes sensor a ball. :/
Another thing is that this g6r was chopping like crazy at an indoor field.

[cire83]

Try setting your ROF lower to like 12.5. see if that makes a difference with the chopping

[Tapok]

Originally Posted by cire83

Try setting your ROF lower to like 12.5. see if that makes a difference with the chopping

i did :/
nothing really
what happens is that i would be shooting ropes with this babe but then it chops and my paint starts going everywhere

[cire83]

let me get this straight set 12.5 in semi mode your chopping paint badly?

[cire83]

Originally Posted by Tapok

but im choping like a mother******
my settings are (frenzy 5.0)
1. semi
2. rof cap 15
3. timer 10 (idk why u need to know this but i still listed lol)
4. debounce 02mS
5. Mech debounce 03
6. trigger filter 06
7.dwell 06.0mS
8. 68 caliber
9.bolt delay 15mS

Is this semi capped or uncapped?

[Tapok]

Originally Posted by cire83

let me get this straight set 12.5 in semi mode your chopping paint badly?

12.5 psp 3
not badly but enough to ruin my game
and basically after a match i come off
clean, lube, etc
then go on and shop again after a while
im using a spire as a hopper

[HeadHunter59]

Do you have any other hoppers you can try?

Just wondering if maybe paint is to brittle. And spire is putting to much force on stack. That bolt it catching the next ball.

Thats only thing i can still think of.

Other wise sounds like faulty eyes. Which happens.

[cire83]

I was playing with mine here... the oled display does have a delay on showing the ball in the breech, and showing the upper eyes(i have 4c). I am doubting an eye problem. unless they are turning themselves off?
like what was already said brittle paint or hopper related.

What paint were you shooting?

[Tapok]

Originally Posted by cire83

I was playing with mine here... the oled display does have a delay on showing the ball in the breech, and showing the upper eyes(i have 4c). I am doubting an eye problem. unless they are turning themselves off?
like what was already said brittle paint or hopper related.

What paint were you shooting?

Yea I guess it's the screen
And i was using Empire HEAT. It's ok paint. What can I do to make my g6r softer on paint? More consistent, smoother, and more efficient? It's not as good as described :/

[gamer565]

Chops and barrel breaks are two very different things. Be sure you know the difference.

If the eyes are not seeing something, then they will not allow the marker to fire.