Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 11-12-2012, 11:56 PM #1
marceldacs
 
 
marceldacs's Avatar
 
Join Date: Nov 2012
Location: Illinois
marceldacs is playing at Living Legends VI
marceldacs owns a Planet Eclipse Ego
marceldacs has achieved Level 1 in PbNation Pursuit
Noobie questions

1. Since a lot of markers operate around 100 psi, will the marker stop firing when the tank reads 100 or will it stop at a larger number than that?

2. Overboring vs underboring. Overboring works for everything right?? Do you just sacrifice small amounts of accuracy?
marceldacs is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 11-13-2012, 12:19 AM #2
gamer565
Place ran by hypocrites
 
gamer565's Avatar
 
Join Date: Dec 2005
Location: OK
Annual Supporting Member
gamer565 is playing at Living Legends VI
gamer565 is playing at Living Legends VII
gamer565 posts videos on PbNation
gamer565 is reppin' sidebar 4 life
gamer565 has achieved Level 6 in PbNation Pursuit
gamer565 is one of the top 100 posters on PbNation
gamer565 is Boss
A lot of marker's do not operate at 100psi..

Most are around 200-300psi, once your tank pressure gets low enough it won't just up and stop on a dime, the velocity will slowly start dropping then when pressure is low enough it will eventually stop firing the paint out the barrel. Depending on the tank reg, will depend on when this starts happening.

Overboring to a certain amount will work for just about everything. Wouldn't go more then .03-.07 larger then the balls, and no more then 0.05 smaller when underboring.
__________________
Jolly Green (╯□)╯︵ ┻━┻

gamer565 is offline   Reply With Quote
Old 11-13-2012, 12:26 AM #3
masterofTHUMBS
boom headshot
 
masterofTHUMBS's Avatar
 
Join Date: May 2007
Location: 703
masterofTHUMBS posts videos on PbNation
masterofTHUMBS is an NCPA player
masterofTHUMBS supports Pev's Paintball
masterofTHUMBS plays in the APPA D5 division
Operating pressure really depends on the marker and the bolt design. For example, on a spyder/tippmann, the gun will stop firing when there isn't enough pressure to recock the bolt. Before this happens though, the shots will probably decrease in velocity even though the gun may still recock. Tank pressure is really only good for estimating how much air is left until pressure starts to get inconsistent.

Overbore is generally less efficient while underbore may be more efficient although harder on cheap paint. Accuracy is determined by the ball shape. It's not something you really can control other than paint choice.
masterofTHUMBS is offline   Reply With Quote
Old 11-14-2012, 10:41 AM #4
junits15
 
 
junits15's Avatar
 
Join Date: Feb 2011
Basically the gun just starts to shoot slower and slower until the balls go like 10"
Operating pressure vary a lot, so there no real solid answer

Underbore if you play pump, and bore to match when playing semi. Over boring decreases efficiency.
junits15 is offline   Reply With Quote
Old 11-14-2012, 10:50 AM #5
Fedo
Who Has More Fun?
 
Fedo's Avatar
 
Join Date: Dec 2009
Location: Bloomington, IL
Fedo owns a Planet Eclipse Ego
Fedo is an NCPA player
Fedo plays in the APPA D5 division
Everyone basically covered it, but not all markers operate at 100 psi. I have meet few that run best there, mostly Macdev I believe. Others prefer between 180-310.
__________________
Illinois State Redbirds

Windy City Punishers

Like us on Faceboook: Illinois State Redbirds Paintball
Fedo is offline   Reply With Quote
Old 11-14-2012, 08:29 PM #6
Darko9989
MacDev Militia
 
Darko9989's Avatar
 
Join Date: Jul 2012
Location: Calvert City, KY
Annual Supporting Member
Darko9989 is BST Trusted
Darko9989 is playing at Living Legends V
Darko9989 is for the Gunfight
Darko9989 supports Pev's Paintball
Darko9989 has perfected Level 3 in PbNation Pursuit
Darko9989 is attending Decay of Nations VI
Quote:
Originally Posted by Fedo View Post
Everyone basically covered it, but not all markers operate at 100 psi. I have meet few that run best there, mostly Macdev I believe. Others prefer between 180-310.
Yeah your right about MacDev. My Clone runs at exactly 100psi.
Darko9989 is offline   Reply With Quote
Old 11-14-2012, 11:08 PM #7
2nwyka
A Lover and a Poet
 
2nwyka's Avatar
 
Join Date: Aug 2011
Location: Fort Collins, Colorado
2nwyka posts videos on PbNation
2nwyka has achieved Level 3 in PbNation Pursuit
Okay, your PSI question:
CO2 and HPA Tanks output 800psi across the board unless they're set for something different (like the Ninja Pro Series or preset Crossfires). Now, most lower end markers will operate directly off of this pressure (Spyders, Tippmanns, Piranhas, etc...) and work just fine. They'll be more efficient at a lower pressure, however. This is achieved by the use of a regulator, which steps the pressure down from anywhere to 400psi to 50psi or less, depending on the reg! Now, these regulators seem to like to sit somewhere around 300psi. My Superstock runs 350, my A5 runs 300, so it's a nice tight number. So, at 800psi left in the tank, it starts to decrease velocity and consistency.

I'd rather underbore, but that's just my inner 'Cocker owner coming out. Underbore will give you better shots, depending on the degree of underbore. Obviously you don't want to use a .670 for paintballs .687 in diameter...that'll not go well for you.
Hope that helped!
Noah
__________________
Learn more about paintball! Articles Videos!!
Colorado Nighthawks
Gearbag Sale!

Rocking drop-forwards like they're going out of style...oh, wait...
Proud Pumper since 2011
2nwyka is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump