Find fields & stores near you!
Find fields and stores
PbNation News
PbNation News
Community Focus
Community Focus

Thread Tools
Old 11-14-2012, 06:46 PM #1
Just gettin' by
stukam17's Avatar
Join Date: Jan 2012
Location: Puget Sound area
stukam17 has achieved Level 1 in PbNation Pursuit
Compatibility Questions

I was asked the following questions about my CCM Series 5 cocker in sig.

1) would a HPA tank with an output pressure of 480psi work? I thought yes, with adjustments to the HPR as the tank output is higher than the needed operational pressure. But was asked to confirm.

2) would this pump kit, 7c03 work properly on the gun? I also thought yes as it is a 2000+ model kit and so is the gun.

Any info is greatly appreciated.
Quality Autococker Parts
stukam17 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Old 11-14-2012, 07:13 PM #2
Darkapollo's Avatar
Join Date: Sep 2007
Location: New Cumberland, PA
No, you will end up starving the reg with low pressure.

Yes, any 2k+ kit will work.
Darkapollo is offline   Reply With Quote
Old 11-14-2012, 07:56 PM #3
Don't eat that....
Rebel_816's Avatar
Join Date: Apr 2007
Location: Lynn, AR
since yours is a mech you might be able to get away with low pressure, cockers run closer to 350psi so it can be pretty close. only way to really find out is try. if it was an e-cocker i agree it would definately be starved for air even at 15bps.
Rebel_816 is offline   Reply With Quote
Old 11-14-2012, 09:51 PM #4
Dk-79's Avatar
Join Date: May 2004
Location: North County, California
 has been a member for 10 years
Dk-79 is reppin' sidebar 4 life
The general rule of thumb is a minimum of 200PSI over your operating pressure.

My STO's sweetspotted at 280PSI, so 480 would be right on the bubble. However, since it's a mech, chances are it wont cause problems with starving.

Though it's better to have it and not need it. A big expansion chamber would help a ton.
Dk-79 is offline   Reply With Quote
Old 11-14-2012, 09:57 PM #5
Kanas's Avatar
Join Date: Feb 2012
I actually purchased it, and plan on turning it into a pump. I a assuming that the 480 would still be fine? I have the ninja pro reg, so it can always be adjusted.
I'm Ben, and I'm addicted....
Check Out Liberty Paintball-
Kanas is offline   Reply With Quote
Old 11-15-2012, 12:58 AM #6
addicted2dunes's Avatar
Join Date: Dec 2011
Location: Orcutt, CA
addicted2dunes has achieved Level 1 in PbNation Pursuit
I'd say it'd work fine for a pump as you are not rapid firing what-so-ever.
"Originally posted by pumzele: If you don't know at least one of them (nuke, wedge, a2d, darkpolo, metalmover, demo222, ect.) I highly doubt you are a regular to this forum..."
addicted2dunes is offline   Reply With Quote
Old 11-15-2012, 11:19 PM #7
SKI008's Avatar
Join Date: Aug 2003
 has been a member for 10 years
I run my T2 on a Ninja reg with all the shims taken out, never had any issues starving the marker. Ninjas and most modern tanks recharge fast enough these days that there isn't much risk of starving the gun at normal ROF.

That wasn't always the case however which is why people recommend HP tanks for everything that doesn't specifically require LP. Back in 2005 or so most tanks didn't have the recharge to keep up at 15+ bps so the extra pressure the HP tanks put out gave some buffer room. Now though with a good reg you don't need to worry.
This line is in remembrance of Jared Wilson, friend and paintball teammate who died on 7/27/2005.
My Old Feedback +1/-0 | CCM T2 | OLED G6R | Entertaining Offers for either/both
SKI008 is offline   Reply With Quote

Thread Tools

Posting Rules
Forum Jump