Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 10-23-2012, 04:36 PM #1
killerfluffybunny
N.E.Blizzard is Back
 
killerfluffybunny's Avatar
 
Join Date: Jan 2009
Location: Augusta, Maine
killerfluffybunny plays in the PSP
killerfluffybunny plays in the APPA D4 division
killerfluffybunny has achieved Level 1 in PbNation Pursuit
killerfluffybunny has perfected Level 1 in PbNation Pursuit
Timing Help

Ok I looked at the links and i still need helps. Autocockers are my Kryptonite when it comes to markers. SO DUMB IT DOWN!!

I have a 1/2 Blocked System X autocker

PICS








ISSUES WITH TIMING

It is firing on the trigger pull back. <---- THAT IS ALL I KNOW!!!
__________________
Proudly Merc'in Fools for:
Bob Long
MAINEPB.COM
Kohn Sports
killerfluffybunny is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 10-23-2012, 11:02 PM #2
dirtraven
 
 
dirtraven's Avatar
 
Join Date: Dec 2001
Location: NY
 has been a member for 10 years
dirtraven is playing at Living Legends VII
dirtraven owns a Planet Eclipse Geo
dirtraven supports Team VICIOUS
switch the 1st and last hose on your 3-way, middle stays where it is. Your current setup is for a slide trigger.
__________________
you know...
------
Vicious Geo3

Good Ole Autococker

Red Camo/Blackened GTi
dirtraven is offline   Reply With Quote
Old 10-23-2012, 11:32 PM #3
Dk-79
SCHWING!
 
Dk-79's Avatar
 
Join Date: May 2004
Location: North County, California
 has been a member for 10 years
pretty sure they used three oring shafts, like dye and shocktech. His hoses are right.

It sounds to me like your sear isn't catching the lug. Take off any air and try to manually cock the hammer by pulling the bolt back. If the hammer catches on the sear and stays locked back, it's all good.

If the hammer just goes back forward, remove the bolt, and using a 1/8th inch allen key, tighten the set screw that's in the top of the hammer one turn at a time until it catches the sear.

Then you can fine tune it, you want the hammer to fall near the front of the trigger pull, but not so close that it's unreliable. Tightening it will make the firing point later in the pole, loosening makes it trip sooner.
Dk-79 is offline   Reply With Quote
Old 10-24-2012, 06:09 AM #4
dirtraven
 
 
dirtraven's Avatar
 
Join Date: Dec 2001
Location: NY
 has been a member for 10 years
dirtraven is playing at Living Legends VII
dirtraven owns a Planet Eclipse Geo
dirtraven supports Team VICIOUS
Quote:
Originally Posted by Dk-79 View Post
pretty sure they used three oring shafts, like dye and shocktech. His hoses are right.
you r correct on the hose for the x-3way.
__________________
you know...
------
Vicious Geo3

Good Ole Autococker

Red Camo/Blackened GTi
dirtraven is offline   Reply With Quote
Old 10-24-2012, 07:45 AM #5
abcito
 
 
abcito's Avatar
 
Join Date: Apr 2001
Location: Massachusetts
abcito is a Supporting Member
abcito is a founding member
 has been a member for 10 years
abcito owns a Planet Eclipse Ego
also make sure your sear spring is seated correctly
abcito is offline   Reply With Quote
Old 10-24-2012, 10:46 AM #6
Jaccen
 
 
Jaccen's Avatar
 
Join Date: Oct 2011
Location: SW Ontario
http://www.youtube.com/watch?v=_3nvh7e14ak

http://www.mcarterbrown.com/ravi/Art...t/ACTroub.html
Jaccen is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump