Dynasty Shocker problem

xxclown · 02-24-2013, 10:25 PM

Busted out my old dynasty shocker and got it working and everything, but iv been getting first ball drop bad, then today I wasn't shooting consistently at all, if I stopped shooting for more then 5 sec, id get the a ball drop...

what could be the problem???

MachineGunCrew · 02-25-2013, 12:44 AM

you should probably clean the reg. lube the bolt. brand new battery. and get back to us.

xxclown · 02-25-2013, 10:33 AM

bolts lubed before every practice, i havnt taken the reg apart yet, so ill do that today. my guy I know also said to reset the board?

xxclown · 03-11-2013, 11:44 AM

i cleaned the reg and lubed the o rings, went to corono it and it would not shoot until velocity was all the way up and it started leaking from that at high velocity.

I dont get it, everything should be nice and clean and working good, is there a way to break in a fresh reg?

any help would be great thanks!

tyronejk · 03-11-2013, 12:46 PM

What's your dwell at?

xxclown · 03-11-2013, 12:49 PM

im not sure, i have not messed with the board yet.

it has an tadeo M5 board, iv herd that you should reset your board after rebuilding the reg. but I wasnt sure.

JL1988 · 03-11-2013, 12:53 PM

Ya I would try raising dwell so you can lower the pressure a bit, since it sounds like your pressure it too high right now.

xxclown · 03-11-2013, 01:04 PM

alright, ill mess with it right now and see if I can check it. I haven't messed with the board in 5 years...

xxclown · 03-11-2013, 01:07 PM

the dwell is at 14-15

would a low battery make it not shoot either?

jim4130 · 03-11-2013, 05:03 PM

xxclown · 03-11-2013, 06:27 PM

man im so stupid, i didnt even think of that till i saw the board battery light was on. ill try it out and let you guys know what other problems I run into.

xxclown · 04-01-2013, 10:13 AM

I went to test it again, fresh batteries fresh lube job, and still it wont shoot...I think the bolt is sticking, or something cause it justs putters a little....

I notice that as i was turning up the velocity trying to get it to work, it was starting to have a slight leak coming from the barrel. A dude said I should replace all the o rings,

but the orings all look fine? I didnt really have any trouble with it until I relube the hyper 2 reg, but I put it back together the same way i took it apart...

I have the board settings to default so the dwell is at like 15-16

jim4130 · 04-01-2013, 04:51 PM

You must have a tight fitting oring somewhere. And anyone who tells you to change all the orings to solve 1 leak is an asshat.

MachineGunCrew · 04-01-2013, 06:04 PM

lol "asshat"

Anyway.. with your shocker sitting there all that time you most likely have a swollen oring somewhere.

xxclown · 04-01-2013, 10:44 PM

alright, when I find some free time I'm going to take it all apart and check every little thing....

but what I don't get is that it was shooting fine, had a bad first ball roll out, but it was fine, then I cleaned everything etc....and now won't shoot....I'll also try to take good pic of the parts to show you what I'm working with.

MachineGunCrew · 04-01-2013, 11:26 PM

make sure you're lubing it enough. sadly some people don't put enough on.

jim4130 · 04-02-2013, 06:46 AM

Quote:

Originally Posted by MachineGunCrew

make sure you're lubing it enough. sadly some people don't put enough on.

Over lubing is a more common cause than under lubing. Both will have the same effect though. But to much just "gums" stuff up.

xxclown · 04-03-2013, 03:15 PM

I just put light layers on all the orings

and should a firing can come out with my ndz bolt, iv never taken it out?