Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 09-30-2012, 04:30 PM #1
kool_aid22
#1 Hater
 
kool_aid22's Avatar
 
Join Date: Sep 2011
Location: Atlanta
Annual Supporting Member
kool_aid22 is BST Legit
kool_aid22 is one of the top 1000 posters on PbNation
kool_aid22 is Legendary
kool_aid22 supports Empire
tank stuck??

i got a ninja tank stuck in one of my shockers..smart parts on/off and it has 3k psi left in it...the top part of the reg started to unscrew so i stopped i want to take it to a local proshop and have it looked at...any suggestions?
kool_aid22 is online now   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 09-30-2012, 05:21 PM #2
EgoOwner147
You down with CPPP?
 
EgoOwner147's Avatar
 
Join Date: Dec 2006
Location: Evington, VA
EgoOwner147 supports Team VICIOUS
EgoOwner147 plays in the APPA D4 division
EgoOwner147 supports DLX Technology
You can always bleed the air of by taking your macro line off and bleedin it out the elbow fitting. Then you can unscrew the reg from the bottle ad take a strap wrench to get the reg off the gun. How'd you get it stuck that bad?
__________________
Too many Urkels on your team, that's why your Winslow

If someone leaves you feedback, stop being lazy and do the same
EgoOwner147 is offline   Reply With Quote
Old 09-30-2012, 07:11 PM #3
kool_aid22
#1 Hater
 
kool_aid22's Avatar
 
Join Date: Sep 2011
Location: Atlanta
Annual Supporting Member
kool_aid22 is BST Legit
kool_aid22 is one of the top 1000 posters on PbNation
kool_aid22 is Legendary
kool_aid22 supports Empire
No idea i think threads are bad ..
kool_aid22 is online now   Reply With Quote
Old 10-01-2012, 11:13 AM #4
Rob @ Ninja PB
 
 
Rob @ Ninja PB's Avatar
 
Join Date: Sep 2010
Location: Chicago, IL
Rob @ Ninja PB works for a Paintball manufacturer
Rob @ Ninja PB owns a Planet Eclipse Ego
Rob @ Ninja PB supports Team VICIOUS
Rob @ Ninja PB supports our troops
bleed the bottle of all of the air inside it. loosen the screws in the bonnet. screw the bottom half of the reg and bottle back into the bonnet until its seated properly. Then tighten to two set scres down and then try to remove the reg and bottle from your smart parts asa.

I have a feeling it could be worn down threads as well but its tough to say for sure until you remove the reg from the ASA and inspect the threads on both products.
__________________
http://www.ninjapaintball.com
http://www.facebook.com/ninjapaintball
NINJA IS PROUDLY MADE IN THE USA - NOT CHINA
Certfied Hydro Test Facility - DOT RIN# G777
NINJA USERS CLUB
Rob @ Ninja PB is offline   Reply With Quote
Old 10-01-2012, 12:39 PM #5
JL1988
 
 
JL1988's Avatar
 
Join Date: Jun 2012
Location: So cal
JL1988 plays in the APPA D5 division
I'd say do what everyone else is saying about bleeding the air in the tank.
The SP on/off always has the pin engaged, thus it can be difficult to remove with air (I know I have trouble sometimes). By bleeding out the air it will remove some if not all the pressure from the threads.
JL1988 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump