 |
09-21-2012, 09:29 PM
|
#1
|
|
Sinister Ops
Join Date: Feb 2008
Location: McDermott, OH
|
Evil Detonator regulator
How the heck do you service/adjust the pressure on one of these?
__________________
Planet Eclipse Etek w/. Star frame, 08 Ego expansion board, Etek 2 regulator, Ego10 OOPS ASA, SLS Cure 3+ bolt w/. inserts, Zick kit, Kila detents, Violent thumbwheel, PE red laser eyes, Shaft 4 barrel kit w/. all backs and fronts, both Bump pistons.
V3 Dye Rotor w/. Virtue board
114/4500 Carleton w/. Myth reg
Ego/Etek Parts FS/T
|
|
|
|
09-22-2012, 01:28 AM
|
#2
|
|
Join Date: Oct 2011
Location: SW Ontario
|
Quote:
ADJUSTMENT
To adjust Output pressure on the
Detonator, first loosen the locking screw
(using a 3/32” Allen key) in the
Adjusting Collar. It is not necessary to
remove this screw, but it does have to
be turned out at least two turns in order
to clear the detent pocket it engages.
Once this has been done, the adjusting
collar can be rotated to accomplish the
pressure adjustment.
PLEASE NOTE: If you are reducing the
output pressure, remember to either
cycle the marker, or otherwise vent the
downstream pressure as the adjustment
is made. Failure to do so will produce
inaccurate pressure readings, and
possible premature wear on the
regulator sealing element.
Once the adjustment has been made,
re-tighten the locking screw, making
sure that it engages one of the eight
detent pockets provided. Because this
screw engages these positive detents, it
is not necessary to tighten beyond
"Finger Snug".
|
http://www.paintballadvisor.com/manu...R%20MANUAL.pdf |
|
|
|
|
09-22-2012, 11:50 AM
|
#3
|
|
Sinister Ops
Join Date: Feb 2008
Location: McDermott, OH
|
Which direction do you turn the collar to achieve + or -?
__________________
Planet Eclipse Etek w/. Star frame, 08 Ego expansion board, Etek 2 regulator, Ego10 OOPS ASA, SLS Cure 3+ bolt w/. inserts, Zick kit, Kila detents, Violent thumbwheel, PE red laser eyes, Shaft 4 barrel kit w/. all backs and fronts, both Bump pistons.
V3 Dye Rotor w/. Virtue board
114/4500 Carleton w/. Myth reg
Ego/Etek Parts FS/T
|
|
|
|
|
09-23-2012, 03:22 AM
|
#4
|
|
Ron Paul = God
Join Date: Jun 2005
Location: The Land of Nod
|
I would just look up the manual, google it. Dont forget to lock it down once you get it set too.
__________________
OLD FEEDBACK!
Why do people do this wanna-be hk thing? I mean hk people dont even play paintball, they just whine and start drama while wearing the weirdest stuff. Its amazing anyone embraces it.
Im putting the Hero back in Heroin.
I want your G6r parts and upgrades, sell them to me, because you wont get anything for them if you sell/trade them with the gun.
http://www.pbnation.com/showthread.php?t=3808906
|
|
|
|
|
09-26-2012, 01:07 PM
|
#5
|
|
Sinister Ops
Join Date: Feb 2008
Location: McDermott, OH
|
Removed all three grub screws, and the macro fitting completely. Now I have two sections. Isn't there a way to remove the pistons/springs to relube the orings? I need to relube/replace the orings because I have a small leak.
__________________
Planet Eclipse Etek w/. Star frame, 08 Ego expansion board, Etek 2 regulator, Ego10 OOPS ASA, SLS Cure 3+ bolt w/. inserts, Zick kit, Kila detents, Violent thumbwheel, PE red laser eyes, Shaft 4 barrel kit w/. all backs and fronts, both Bump pistons.
V3 Dye Rotor w/. Virtue board
114/4500 Carleton w/. Myth reg
Ego/Etek Parts FS/T
|
|
|
|
|
10-14-2012, 01:34 AM
|
#6
|
|
Pump Playa
Join Date: May 2011
Location: North Vancouver
|
Just check the manual
|
|
|
|
|
10-15-2012, 09:26 AM
|
#7
|
|
Join Date: Sep 2010
Location: Chicago, IL
|
Quote:
Originally Posted by msweeneygt
How the heck do you service/adjust the pressure on one of these?
|
Please read page 3 of the manual for instructions on how to disassemble and put it back together again. It will be at the bottom of the page where it says "Routine Service" |
|
|
|
|
10-15-2012, 12:29 PM
|
#8
|
|
Fear my Join Date
Join Date: Aug 2003
Location: Chapel Hill, NC
|
Quote:
Originally Posted by msweeneygt
Removed all three grub screws, and the macro fitting completely. Now I have two sections. Isn't there a way to remove the pistons/springs to relube the orings? I need to relube/replace the orings because I have a small leak.
|
There's a snap ring you need to remove to get at the internals, they come out of the top if memory serves. Reading the manual would be your best bet.
__________________
This line is in remembrance of Jared Wilson, friend and paintball teammate who died on 7/27/2005.
My Old Feedback +1/-0 |
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
