Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 08-01-2012, 03:21 PM #1
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit
E2 Eblade

So I just got playing paintball again. And I pulled out my E-Bladed Cocker and it seems like from sitting for so long that the solenoid died. It looks like the grease from my lower internals leaked down into the top of the frame while it sat. Does anyone know of anyone who is still an E-Blade Tech or whatnot. I want to get my cocker check out and see if my E-Blade is still able to work or if it is shot all together and I need to get a new one. Thanks
brownellts7 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 08-01-2012, 03:34 PM #2
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit


Figured I would post a picture of the cocker for the hell of it.
brownellts7 is offline   Reply With Quote
Old 08-02-2012, 12:18 AM #3
Rebel_816
Don't eat that....
 
Rebel_816's Avatar
 
Join Date: Apr 2007
Location: Lynn, AR
the sear solenoid? its pretty rare for them to just "die", might just need to take it out and clean the old gunk off of it, or make sure the grips arent on too tight, that can keep it from moving too.

try cleaning it off first, dont put any kind of lube on it afterwards, leave it dry.

if that doesnt work, they arent too hard to find in the bst area here or on customcockers.com
__________________
Rapper
Rebel_816 is offline   Reply With Quote
Old 08-02-2012, 11:39 AM #4
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit
Ok so I just tossed a new battery in and I was mistake the sear solenoid is fine. But I do still have a problem. For some reason the magnetic return isn't returning it after the solenoid fires. Any suggestions?
brownellts7 is offline   Reply With Quote
Old 08-02-2012, 11:54 AM #5
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit
When I loosen the screw on the triggers roll pin the magnetic return works. But I am afraid with it being loose that it will back out over time causing more problems.
brownellts7 is offline   Reply With Quote
Old 08-02-2012, 03:23 PM #6
hmcl281
 
 
hmcl281's Avatar
 
Join Date: Dec 2003
 has been a member for 10 years
not sure why the trigger would fit your sear issue unless the trigger travel does not back out far enough for the opti sensor. under the sear there should be a spring that causes the sear noid to be return to the starting position.
__________________
hmcl281 is offline   Reply With Quote
Old 08-02-2012, 03:28 PM #7
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit
I don't have a sear issue. I thought I did but was wrong. My problem was with the magnetic return not return the trigger like it was suppose to but I think I have solved that issue.
brownellts7 is offline   Reply With Quote
Old 08-02-2012, 03:51 PM #8
hmcl281
 
 
hmcl281's Avatar
 
Join Date: Dec 2003
 has been a member for 10 years
there are set screws for the magnetic trigger return, just screw it closer towards the magnet

or you pin that hold the trigger in might need to be clean
__________________
hmcl281 is offline   Reply With Quote
Old 08-02-2012, 04:01 PM #9
brownellts7
 
 
brownellts7's Avatar
 
Join Date: Jul 2012
Location: Haverhill, Mass
brownellts7 plays in the APPA D5 division
brownellts7 has achieved Level 1 in PbNation Pursuit
How hard is it to take that pin out?
brownellts7 is offline   Reply With Quote
Old 08-02-2012, 04:22 PM #10
hmcl281
 
 
hmcl281's Avatar
 
Join Date: Dec 2003
 has been a member for 10 years
Quote:
Originally Posted by brownellts7 View Post
How hard is it to take that pin out?
you have to take the frame off of the body, from there there is a set screw above the trigger. once you loosen the screw, you just push out the pin.
__________________
hmcl281 is offline   Reply With Quote
Old 08-22-2012, 08:58 PM #11
yoyi4040
Ninja-Flex'n
 
yoyi4040's Avatar
 
Join Date: Jul 2012
Location: North Jersey
yoyi4040 has achieved Level 1 in PbNation Pursuit
yoyi4040 has perfected Level 1 in PbNation Pursuit
It doesn't work. Sell me the E-Blade.
__________________
When the people fear their government, there is tyranny; when the government fears the people, there is liberty. Thomas Jefferson

*If Your Parents Dont Pay For Your Paintball Stuff, Put This In Your Sig*

Jerseys and pants sale. Autographed Ollie Lang LOOK!

Pods and packs for sale
yoyi4040 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump