Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 05-04-2012, 03:08 AM #1
demon16v
 
 
Join Date: May 2012
Location: South NJ
etha feedneck help

The feedneck on the etha is a little to small to fit my Halo 2 loader in it. I've been told that the Halo feed part is a little bigger than some other loaders. So, my question, is there another feedneck that would be better or can I heat the etha one up to give it more room (to fit the Halo) without breaking it or melting it?
demon16v is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 05-04-2012, 03:31 AM #2
theblindchicken
49'er
 
theblindchicken's Avatar
 
Join Date: Jun 2011
Location: Long Beach, CA
theblindchicken is an NCPA player
theblindchicken is an NCPA National Champion
theblindchicken plays in the APPA D5 division
You could remove material from the out part of the halo feedneck if there isn't that much of a difference between the outer diameter (OD) of the halo feedneck and the inner diameter (ID) of the etha feedneck.

You could also get a clamping feedneck if those are available.
theblindchicken is offline   Reply With Quote
Old 05-04-2012, 03:48 AM #3
demon16v
 
 
Join Date: May 2012
Location: South NJ
Thanks. I thought about shaving a little off both but wanted to keep the Halo stock so I could use it on my other gun. I have seen that CP makes clamping feednecks but I'm unsure if the Etha is the same size as regular PE gun.
demon16v is offline   Reply With Quote
Old 05-08-2012, 12:20 AM #4
sumsemperfi
the fat guy
 
sumsemperfi's Avatar
 
Join Date: Dec 2006
Location: Shawnee, OK
sumsemperfi has achieved Level 1 in PbNation Pursuit
sumsemperfi has perfected Level 1 in PbNation Pursuit
im sure you can sand the neck down on the halo.. and not have any issues..
__________________
THERE IS A FAT KID ON EVERY PAINTBALL TEAM. IF YOU ARE THAT FAT KID, PUT THIS IN YOUR SIG
sumsemperfi is offline   Reply With Quote
Old 07-31-2012, 12:20 AM #5
FIERC3Punisher
It is what it is.
 
FIERC3Punisher's Avatar
 
Join Date: Jan 2012
Location: Springdale, AR
FIERC3Punisher is playing at Living Legends V
FIERC3Punisher has achieved Level 3 in PbNation Pursuit
FIERC3Punisher is attending Decay of Nations VI
FIERC3Punisher supports Empire
Mine fit just fine. Or sell the pos hopper and buy a rotor like I did.
__________________
http://www.pbnation.com/showthread.php?t=4021057 JT impulse!
FIERC3Punisher is offline   Reply With Quote
Old 07-31-2012, 06:12 PM #6
straptrams91
PRESIDENT
 
straptrams91's Avatar
 
Join Date: Jul 2006
Location: Pittsburgh, PA
Annual Supporting Member
straptrams91 plays in the PSP
straptrams91 is playing at Living Legends V
straptrams91 is playing at Living Legends VI
straptrams91 supports Team VICIOUS
straptrams91 is an NCPA player
straptrams91 is Legendary
just sand down the OD of the halo shell. shells are much cheaper to replace if it breaks than replacing the feedneck.
straptrams91 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump