[dehr]

Originally Posted by rudz

Both

I like it when you get wet and talk dirty

Well then I'll come play wcppl with you

[msonic]

*Tried everything on my BL and it wont work*

*Better buy Eclipse*

/meme

[alphanu22]

Originally Posted by Kaotix

HELP HELP HELP HELP

So I have switched every part imaginable except the black manifold part between the body and the frame and nothing helps.

Gun airs up. no leaks. Pressures are at 80/190 HP poppet
Gun will cycle enough to properly move the ram and bolt but not enough to smack the poppet hard enough for air to come out of the bolt.

Replace Rear Ram Oring // Replace the Rear Ram Cap Oring (with the right size)

[Kaotix]

Hey bjorn.

The new noid I tried at my proshop HAD to be a dud.

I swapped in the noid and the noid...carriage? (The black piece) from my 2012
And it worked.

[alphanu22]

the Gasket, you prolly had it on there backwards... put the "new" noid back on there and see-

[Kaotix]

OH FOR !!!!!!!!!!

The frigging screw put through the noid into the black piece /manifold thing might as well of been cemented in!!!

uhhhhhgg.... Would you guys believe this is the third g6r I've worked on where the screws were put in / not machined well at all that screws strip and have to be machined out.

[alphanu22]

sorry, but ive worked on alot of BL's and have yet stripped a screw-

[Kaotix]

Sorry Bjorn... 7 hours of frustration later...

So providing with me swapping parts back and forth and back and forth to isolate the problem...

if I did the swapping correctly I have reason to believe it's the black piece the noid screws on to. Is it possible that it would get gunked up and restrict air flow drastically?

So the black piece is the Manifold? What is the square rubber piece that goes in between the two called?

[alphanu22]

Originally Posted by Kaotix

Sorry Bjorn... 7 hours of frustration later...

So providing with me swapping parts back and forth and back and forth to isolate the problem...

if I did the swapping correctly I have reason to believe it's the black piece the noid screws on to. Is it possible that it would get gunked up and restrict air flow drastically?

So the black piece is the Manifold? What is the square rubber piece that goes in between the two called?

The Main Black Deal is the Manifold. What is between the Solenoid and the Manifold is the Gasket-

[dehr]

Someone is a noob with guns

[stormtrooper123]

Hey been gone for a while looks like not much is happening but gun problems...

[dehr]

Might have my luxe gone. Wouldn't mind that

[ck028]

Originally Posted by stormtrooper123

Hey been gone for a while looks like not much is happening but gun problems...

Another day, another problem. That's the result of a fine tuned machine being messed with.

[OSU1989]

Would like to apply.



Best gun that I have ever owned and/or shot.

[sharkethic86]

Originally Posted by OSU1989

Would like to apply.

Best gun that I have ever owned and/or shot.

Hell yea man. Nothing compares to a nicely tuned G6R.

[rudz]

I hardly ever mess with the manifold or solenoid, once I had a manifold oring on the ego go dry, and I had to lube it. Once in 3 seasons of heavy use

And my BL/ICD Defiant1, but the poor thing was so old, what do you expect, lol

[PremiumHHH]

I will be making V3, at about 3:30 PM PST! SO wooo!

[Kaotix]

Alright.

New day. Time to make it a better one.
CMON New Thread!

EDIT - Nevermind... the battery connector sprig on my board fell off while pushing my solenoid wires into place.

[msonic]

Send the gun to blast before you do anything else.

[f8al]

Agreed.

Sup doods?

[sharkethic86]

Bored at work pretty much.