Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 10-26-2011, 08:32 PM #1
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
Demon Semi

I turned my Demon on today and noticed it had switched to 10.4 BPS but I know I left it at 12.5 BPS. Shot a little with it then turned it off to put away. Maybe 15-20 minutes later I went to turn it on to see if it had changed back down to 10.4 BPS and it had done it again.

What could have caused this? What should I do if it does it again?
OR Baller, CST is offline   Reply With Quote
Old 10-26-2011, 08:54 PM #2
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Hhmmm, unplug the battery for 15 min to reset the processors. Then try it again see if it happens. Please let me know also make sure non of your buttons are stuck.
SHOOTNPOO is offline   Reply With Quote
Old 10-26-2011, 09:09 PM #3
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
Thank you Eric, I will try that tomorrow when I can get to my marker.
OR Baller, CST is offline   Reply With Quote
Old 10-27-2011, 07:40 PM #4
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
So if I switch my gun to PSP (which is set to 10.4) then back to Semi, semi becomes capped at 10.4. Is it possible to keep PSP at 12.5 because I'll turn the gun off and it goes back to 10.4 if I turn it off then on again.
OR Baller, CST is offline   Reply With Quote
Old 10-27-2011, 07:49 PM #5
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Let me look into this alittle further for you and do some tests tonight.
SHOOTNPOO is offline   Reply With Quote
Old 10-27-2011, 07:50 PM #6
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
Ok thank you Eric.
OR Baller, CST is offline   Reply With Quote
Old 10-28-2011, 11:26 AM #7
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
With turning the marker to psp it defaults to 10.4. Switched to semi it went to 10.4
Then set ROF to 12.5, then switched back to psp and ot defaulted to 10.4 as preset.
I tried with 4 different boards and it did same thing.
Switching fire modes with a per determine default setting is how it works. Their is no save mode.

With that you just have to set it manually.
SHOOTNPOO is offline   Reply With Quote
Old 10-28-2011, 02:26 PM #8
jason_vanguard
Valveflow Ltd
 
jason_vanguard's Avatar
 
Join Date: Nov 2009
jason_vanguard works for a Paintball manufacturer
jason_vanguard is for the Gunfight
jason_vanguard is for the Gunfight
Strange

Only time I can remember seeing this sort of issue was on an older software version, just for the fun of it let us know the version on your board, long shot but worth a quick check.
__________________
Jason
Valveflow Ltd

jason_vanguard is offline   Reply With Quote
Old 10-28-2011, 02:43 PM #9
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
Eric thank you for checking. Exactly what mine does. I'll just deal with switching as needed.

Jason I will get back to you on the version since I'm at work and have no access to it yet.
OR Baller, CST is offline   Reply With Quote
Old 10-28-2011, 03:08 PM #10
OR Baller, CST
 
 
OR Baller, CST's Avatar
 
Join Date: Aug 2011
Location: Corona, CA
OR Baller, CST plays in the PSP
OR Baller, CST plays in the APPA D4 division
OR Baller, CST supports DLX Technology
It is version 1.01 (en)
OR Baller, CST is offline   Reply With Quote
Old 10-28-2011, 10:00 PM #11
proto_oli
INERTIA
 
proto_oli's Avatar
 
Join Date: Jun 2009
Location: Puerto Rico
proto_oli plays in the PSP
proto_oli supports DLX Technology
yep, mine does the same thing.. doest bother me much since its an OLED board and easy to program.
__________________
DaLuxeMob
proto_oli is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump