[zzANGUISHzz]

Originally Posted by matt3

Ok, got my new shocker eyes in and installed. Quick recap of the issue. Freeflow shocker, virtue redefined board. Eyes off no ball, eyes read no ball will shoot normal 12.5 bps. Eyes on no ball, reads no ball will not shoot. Eyes on with ball reads ball shoots, but drops ramp down to 6bps. What to try next? Gotta be the board/settings..... I have looked but don't see a way to adjust that. It is set at 12.5 already.... Already reset the board to factory as well. Suggestions???
Thanks
Matt

MROF "eyes on" 12.5+? Is this set right?

[jim4130]

Check your eye setting (flickering yellow) could be reversed and giving you an eye malfunction and capping the board to 8bps.

[skateandpaint]

will the sft reg leak if the bottom set screw is missing?

[jim4130]

No.

[matt3]

Read the manual a bit more. Just put a hopper through it. Nothing like the sweet sound of a shocker ripping :-) also just got my order from McMaster.... More orings to try lol.

Thanks for all the help. Looks good so far

[dreadedkaos]

hey guys, got a small problem with my nxt.. I can't seem to get the eye covers off on one side, any ideas?

[R2-D2]

plunger

[Box]

JBWeld on the tip of an allen wrench perhaps? let it cure and twist it out?

If not, you'll have to drill it off, not a great time.

[dreadedkaos]

greeaaat. got em off, and sure looks like the eyes are busted. ty for the help guys.

[paintballpunker]

Bought the hybrid print dynasty shocker todd martinez built years ago,
I decided to do a complete rebuild seeing as though this thing likely has over 1,000,000 paintballs through it's breech.

When I took the bolt assembly out of the body, I realized that I had a stock firing can with an HE bolt. I have been trying to fish that sealing oring out by shoving the oring pick into the can with the bolt slid forward, backwards, halfway everything with no luck.

Any advice on tricks to get that dang oring out? and furthermore how to go about putting a new one on while it is buried inside the firing can?
Thanks guys!

[jim4130]

First things first push the whole can out with the bolt inside. Then work on it from there sometimes you can wiggle it past the rear can oring. When you put it back together dont use that oring its useless in a stock can because the stock can doesnt have the surface. To seal against it.

[paintballpunker]

ended up wiggling it past the rear- thanks jim!!

now let me get this straight,
I have a stock firing can (one hole between the two o rings and not able to separate the cap) so it is useless to put the HE sealing Oring that was keeping the bolt stuck in the first place?

[Apollo918]

Correct. Reinstall without the HE oring.

[paintballpunker]

this was the best free service i've ever received from the paintball community.
yet another reason this shocker will remain in my possession till i'm dust!

[paintballpunker]

I have returned!

So I replaced every o-ring including non-sealing.
lubed it well,
air it up and shoot the first shot with some fsdo as expected, second and third had slight drop off as well. Fourth shot had full pressure, then the fifth dry fire sticks the bolt forward with air rushing out of the solenoid.
I shove the bolt back and click the solenoid to find that now it just stops the air flowing out of the noid, and when i fire again the bolt does nothing while the air starts rushing out again.

tl,dr:
first shot is fine, second shot sticks forward. When bolt is shoved back air rushes out noid and stops/starts with the trigger

[AndrewTheWookie]

Try swapping out the bolt sail o-ring.

[americanidiot748]

ok, maybe you guys can help, i'm thinking its the bolt sail O-ring but i could be wrong, shocker has full stock SFT internals with HE guide...it has a very small leak down the barrel, so slight in fact you have to hold your ear to the feedneck to hear it...it is not sprung, and i tried cleaning/lubing it and changing the Can/sleeve orings...

[inmylife2415]

Front guide oring

[americanidiot748]

lol, of course the one i dont have! lol, looks like i'll be hitting up oringmonkey

[p8ntballer101]

my shocker leaks slowly from the bolt if i put my finger in front of it i can feel the air. should i get new o-rings or what?

[jim4130]

If it feels like its coming from inside the bolt it's your front bolt guide tip oring.
If it feels like its coming from around the outside of the bolt it's either the front inner or front outter can oring.