[tyler151]

sft leaking problem! got a leak comming from the breech, Ive replaced the bolt guide o rings and the o rings inside the can . i still have a very, VERY small leak still comming from the breech, can hear it comming from the qlock and barrel but you have to put your ear up to the gun.. WTF?! and is there a better option for the inside can orings than the regular black o rings? as the ones i pulled out were clear/yellowish?

[Apollo918]

hbnr orings are better. They hold up a lot better but are hard to source sometimes. Make sure the orings are lubed really well. And cycle the bolt a few times. If the bolt guide orings, front inner can oring, and front outer can orings are all good, then there should not be a leak down the breech.

[inmylife2415]

There are lots of places to get HBNR

[vesparider]

Got this SFT from the field owner. He said its been under the counter for a couple years. No one claimed it and it leaks. He wasn't gonna mess with.

Problem: Start putting air to it.

1. Pushes bolt all the way forward and leaks out the left side of manifold after doing so.

Stock internals Parker Solenoid

Replace all 6 metric Orings in manifold. I even put my Engine out of my working SFT and it does the same thing.

Any thoughts?

[bcrguy]

check o-rings in the noid itself..

[jim4130]

The front cap of the noid my be upside down.

[vesparider]

Butterfly o rings loo to be in good shape with no visible issues.

I seen the difference in the top cap and how it suppose to be fitted. Rotated it 180. Now just have a leak down the barrel. Will go back into it tomorrow. Thanks for the help. May be on the right track now.

[bcrguy]

barrel leak check sail and front o-rings on the can and bolt guide.

[jim4130]

Originally Posted by bcrguy

barrel leak check sail and front o-rings on the can and bolt guide.

A bolt sail will not produce a barrel leak. Front inner and outer can rings and front bolt guide ti ring are what to look for.

[fsrxc1]

This man knows what hes talking about right here

P.S- You Sally take the Gmax to BP with me

[firefoxx04]

possibly trading a nice closer for this shocker. ive been wanting to try a shocker. He says this is a dynasty shocker.



has aka reg and HE sprung bolt, dynasty board. should i expect any issues with this gun? i know these guns do not get good efficiency in stock form but what about with this bolt?

this is the gun im trading.. i feel that i should make him add but im not sure

[tyronejk]

I think he should add ~100. That's a nice closer, btw.

[jim4130]

Originally Posted by fsrxc1

This man knows what hes talking about right here

P.S- You Sally take the Gmax to BP with me

Perhaps.

Yes shocker adds for closer.

[firefoxx04]

thats what i was thinking, thanks guys.

its a great shooter but i have two of them..

[JL1988]

My bolt bumper (the one the sits on the bolt guide) is destroyed. Where can I get another or can I use an oring instead?

[jim4130]

Oringmonkey has some nice extra hard ones to help against sprung bolts.

[510waffles]

http://www.pbnation.com/showthread.php?t=3910854

made a thread, no one came to help

[jim4130]

Inspect your wire harnesses for loose/damaged wires.

[eatafetus]

I have a virtue led board. On my SFT project, it seems like the eye is working in reverse. When I block it, it won't fire. When I don't, it fires.

This test was done off-gun in a dark room. I just connected the electronics and then held the ribbon in my hand, used finger to block eye.

I'm wondering if I need a new eye ribbon? Or am I testing it wrong?

[Apollo918]

Switch the eye logic. Breakbeam vs reflective will cause that. It's flickering yellow.

You will be set.

[jim4130]

^^^
.