[fishballer06]

Originally Posted by Box

any idea why an Evolve SS manifold wont allow solenoid spacer screws in it?

I tried to screw the solenoid on, and it felt like the spacer screws were tight and they just snapped. It was like the manifold screw hole was slightly to small

It could be because the Evolve manifolds required their own specific type of spacer screw

[SingaporeSlayer]

hello Nation I have a quick question. I know ive come accross this somewhere but cant seem to find it now.
Question: i have a nxt octane shocker with RL board will that board fit into my sft shocker?

[fishballer06]

All lower boards are compatible with ALL frames.

[iamthanos]

So i installed a new solenoid in my shocker and now when i fire the gun the solenoid clicks but the gun doesnt fire. The end cap is installed correctly and i replaced the battery. and the dwell is set to 12. any other idea what it could be?

[BTrain]

Have you tried raising the dwell? I have mine set at 13 currently and it takes 2 shots to fire. Normally around 15 my NXT fires perfectly.

[fishballer06]

It should puff at 12, regardless of what solenoid is in it. I'm betting your reg is set way too low and/or your battery is dying.

[lillybudjr]

Hello, are GOG eXTCY eyes compatible with shocker NXT? Thank you for you time.

[alfredg]

If I had say.. a body with speed BB milling done and a virtue OLED board and a speedy chip, but no eyes, what can I do? Doesn't look like speed eyes are easy to come by.. Virtue OLED has a BB mode, so I assume I wouldn't need the speedy chip, right? Would speed's milling allow me to put another set of eyes on? Would I be able to plug it into the upper board?

[Japy]

Speeds eyes should be set to reflective. despite being a breakbeam eye.

[lillybudjr]

Originally Posted by lillybudjr

Hello, are GOG eXTCY eyes compatible with shocker NXT? Thank you for you time.

Disregard my last, I contacted www.smartparts.com or GOG "It's like a split personality" they carry the break beam eyes in stock. Yay!

GOG eXTCy eyes are not compatible with the shocker NXT. Hope I could help anyone with the same question.

[Box]

Originally Posted by fishballer06

It could be because the Evolve manifolds required their own specific type of spacer screw

You've got to be ****ing kidding me. That would explain that whole situation then. It doesn't seem to make much sense to use a proprietary screw there beyond what Smart Parts did originally. You know the threading on those fish?

On a side note, finally got all the parts for the Shego's firing assembly and I'm stoked. Delrin sleeve, NDZ Adjustable bolt guide, NDZ Speed bolt (Sprung/QEV), and a NDZ ULP Can stuffed into an Approval Naughty dogz body. Excited to have autococker threads on it.

[radair221]

Hey guys I'm new to shockers just purchased a nxt off of eBay and when i went to put a battery in it I ran into a few issues. First when i plug the battery it the marker turns on and chirps then the on off button chooses when it wants to work. Also it will just randomly turn off and on and change into eyes on or off on its own any ideas on what this might be? Thanks in advance

[jim4130]

Your power switch on the upper board is sticking. Could be the button in the frame sticking. Could be the wire harness stuck between the the button and switch or it could be a bad switch all together.

[radair221]

OK thanks its not the button sticking and the harness isn't in the was so that leaves the switch. Do u know if I can purchase just that and where or do I have to purchase the whole upper board?

[jim4130]

You can buy the switch from zdspb.com. soldering is required for that repair.

[lillybudjr]

Originally Posted by radair221

Hey guys I'm new to shockers just purchased a nxt off of eBay and when i went to put a battery in it I ran into a few issues. First when i plug the battery it the marker turns on and chirps then the on off button chooses when it wants to work. Also it will just randomly turn off and on and change into eyes on or off on its own any ideas on what this might be? Thanks in advance

I am gonna take a guess by the chirp you hear when powering on your marker you have a Blackheart board. Just a guess. But make sure after you troubleshoot your current problem you perform a factory reset and ensure you have break beam eyes turned on and NOT REFLECTIVE. I made this mistake a while back.

[Japy]

If I want to blow out any debris from within my insert tubes what's the best method? Just remove them and feed like 50psi to the gun? Do I leave the bolt in? Do one at a time?

[ItsthatmanB]

Have a shocker NXT that I played with on Sunday. Cleaned and stored safely after. Took out today to play and I'm not getting air through the barrel, but instead it comes from the trigger frame. I'm thinking solenoid but would be open to hear some better news.

Last played indoors with compressed air and I haven't changed the dwell settings.

[Japy]

Probably orings. Check zdspb.

[ItsthatmanB]

Originally Posted by Japy

Probably orings. Check zdspb.

Thanks. I have taken a look and I think an inaccurate gauge is the problem. Will disassemble and replace o-rings tonight. Again, Gracias!

[desacato102]

Yeah I need to change the pin on my on/off switch(nxt) and not even the smallest allen key fits. Can anyone tell me the measurement?