[jason_vanguard]

Originally Posted by gildy1

My back cap on my demon use to unscrew itself, so I added 2 orings to the blackcap to make it a squeeze, solved the issue, but is this normal

It can happen yes,
The 3 start thread we use can sometimes vibrate loose, either your o ring fix or simply nip the drivetrain in with the Allen key should suffice.

[smwpaintball1]

Originally Posted by jason_vanguard

Hi,
Where is it loose?
If its the inner top part "the bonnet" then either use circlip pliers or an Allen key, if its the whole assembly then just tighten it in with your hand.

Where the reg meets the body

Nvm there is a nut under the reg core that was lose

[jrred17]

Originally Posted by ravenwpg

i have the same question as WOAH : hey i just got a creed that was set to low pressure but i use high pressure so i was wondering what i should due to the lpr, and board settings? i know i will have to adjust the velocity too most likely

.

[subaruu]

mine did not come with a manual so i dont know.....what is standard maintenance for a V2

[MoogLe]

wow.... nobody can answer my questions???

[overweightangel275]

Originally Posted by MoogLe

wow.... nobody can answer my questions???

Pm'd sorry for the delayed response

[XSTIFFXPAINTBALLERX]

hey so I'm having problems with my creed i first had a leak down the barrel i replaced the oring in the lpr assembly and reset the hpr and lpr setings but now there is a big leak coming from the grip and trigger frame area i have no idea how to fix this please help

[overweightangel275]

Originally Posted by XSTIFFXPAINTBALLERX

hey so I'm having problems with my creed i first had a leak down the barrel i replaced the oring in the lpr assembly and reset the hpr and lpr setings but now there is a big leak coming from the grip and trigger frame area i have no idea how to fix this please help

What did you reset them to?

[XSTIFFXPAINTBALLERX]

I have a high pressure tank so I set the hpr all the way in then turned it one turn out and I winded the lpr all the way out and started to slowly wind it in until the bolt cycled but when I started to wind the lp in it started leaking more and more

[Reaper (ACI)]

Originally Posted by XSTIFFXPAINTBALLERX

I have a high pressure tank so I set the hpr all the way in then turned it one turn out and I winded the lpr all the way out and started to slowly wind it in until the bolt cycled but when I started to wind the lp in it started leaking more and more

Take the HPR out another 1/4-1/2 turn. Then bottom out the LPR again. Turn it in until it is about 1-1/2 or 2 threads out from flush. Then shoot it over the chrono. See if that stops the leak.

[woah]

so i have a creed set for lp and i use hp is there any hints i should know before i try to tune it?

[overweightangel275]

You can always go back to zeroing out the regs (HPR and LPR) and rebalance everything. Typically I would do this before hand, with an LP setup. You pressure may be a bit high when you go to use a HP tank. Turn the LPR adjuster all the way out and then turn the HPR all the way in. With air in the gun turn the HPR to 1 turn and then turn the LPR in until the marker cycles fully. If you can does this over the crony with some paint you should be all set. Let me know if you need help with anything else.

mike@vanguardpaintballusa.com

Originally Posted by woah

so i have a creed set for lp and i use hp is there any hints i should know before i try to tune it?

[XSTIFFXPAINTBALLERX]

ok so I tried that and I'm still leaking from the top of the grip frame
below the solinoid

[overweightangel275]

Check you 15x2 orings on the LPR body. They may be damaged.

[Noxious_6]

Hey, my creed is leaking out of the rear port in the noid, its a small, squeaky leak. gun still works and leak doesn't seem to change when fired. seems to disappear if i cover it with my finger. any help appreciated

[Mclovin101]

Ive just picked up a creed from a friend. All good but Ive noticed he has rounded the back cap off. Now does anyone know how to get it off.

[XSTIFFXPAINTBALLERX]

Originally Posted by overweightangel275

Check you 15x2 orings on the LPR body. They may be damaged.

replaced them and it is still leaking from around the solinoid

[overweightangel275]

Around? You might have a bad gasket noid gasket

[Pr1m0]

So my demon.

Air it up and it shooots fine!

5-6 games later I get a HUGE leak from the reg area. From where the reg screws in the body. I unscrewed the reg.. screwed it back on and the leak goes away. Happens again later in the day. The owner before me mentioned he had unscrews the powercore while the gun wwas still aired up.

Any ideas here?

[owengoin]

the left eye cover on my demon will not come off... help please?
pm me with suggestions please

[ky7jg]

solenoid area/lower bolt area has a small leak. ive checked the o-rings on the bolt, the gasket that is attached to the body (idk what its called), and the o-ring that is exposed when you separate the the frame and body. what do i do?