[SHOOTNPOO]

No, the ram should come out with ease. Their is an inner valve oring that the ram glides on but that is it. Make aure you are pushing in the ram.
What you can do is put the bolt back
In and see if the ram moves freely. If it does it will come out the back of the marker easily.

Eric

[xxdeadshotxx]

I'm having some major problems with my creed right now. The first problem I have is that it is leaking somewhere out the valve body or ram. Second, I can't get it to fire above 210fps. Third problem is that that the gun is firing with the lpr zeroed out and the hpr only 1/2 turns out. I replaced all the o-rings on the lpr and hpr along with the poppit. BTW, is have the light weight ram, delrin bolt and lp poppit. Eric, is there any way to send you my marker and have you check it out? How much would it cost?

[p-baller100]

Yeah I'm positive It's the valve guide. replaced the right size oring 4 times. Everything else seemed to go out on me too. Had to rebuild the HPR, I don't know why this all happened on a marker with less than 8 cases on it but aw well. Sent you a PM SHOOTNPOO

[Nemo128]

What do you recommend as a starting point for the HPR if running a Gorrilla Air Myth G2 mid-pressure reg? It supposedly puts out between 650 and 750psi. I'm guessing 1 turn out to start.

[SHOOTNPOO]

I would start at 1 1/2 turns out.
Run dwell at 11 to break in the marker.

LPR may be close to flush.

Eric

[Sick420]

What is the size of the flat o-rings on the bolt? Mine are worn out and about to rip soon.
Thanks

[SHOOTNPOO]

015 Xring

[p-baller100]

So I got a new valve guide, the new bolt (modded by pooty), the lp poppit, and the lw ram. I also jumped from the .689 stock to a .682 disruptive (From what everyone says, will raise fps over most any other barrel, comparable to a lotus) which is a slight under bore for the marbs I am using. How should I go about setting it up? atleast to start? I have it set at a dwell of 11 hpr at one turn out and lpr at one turn out and I'm gettin like 220 fps. Is there a break in period? I want it set up for smoothness not so much efficiency. But any what would be your recommendations?

[SHOOTNPOO]

Adjust the LPR to chrono at desired FPS.
the HPR can go out to 1 1/2 if you need to but would try to get it done at 1 turn out on the HPR and adjust the LPR to desired FPS.

Eric

[p-baller100]

Yeah I was at 3-4 turns out on the hpr and maybe a 1/4 out on the lpr with a dwell of 10-13, nothing worked. But I shot you a PM.

[noonagon]

Dear Mr. Poo,

Wondering a couple of things;

I have about 10 cases through my creed, is this considered "broken in"

When the manual says screw the her all the way in then out 3/4 to 1 turn is this gased up or degased?

What are the best settings I can start out with to reduce the kick of my creed/give it a smoother shot. Shooting psp

Does anyone else have a problem breaking/chopping the last one or two balls in a ball stack (rotor and shooting psp)

Thanks

[SHOOTNPOO]

Originally Posted by noonagon

Dear Mr. Poo,

Wondering a couple of things;

I have about 10 cases through my creed, is this considered "broken in"

When the manual says screw the her all the way in then out 3/4 to 1 turn is this gased up or degased?

What are the best settings I can start out with to reduce the kick of my creed/give it a smoother shot. Shooting psp

Does anyone else have a problem breaking/chopping the last one or two balls in a ball stack (rotor and shooting psp)

Thanks

The 10 case rule is a great way to know your marker has done its best to get seated in with the Orings and such.

As for the settings on the HPR, you can do it either way but recommend Gases up.
1 turn out on HPR
Adjust LPR to chrono at desired FPS.

Now with the marker being broken in you can start tuning the dwell down to give yourself a more consistent shot and better efficiency.

Now the Breaking paint of the Last 2-4 balls in the hopper is in the Timing of the marker and having no pressure on the stack of paint.
Timing meaning (dwell) you need to adjust the dwell to when you are firing over the chrono you are getting better consistency in FPS. if you go to low on the dwell it will be jumping all over the place on the chrono. It will also help with the timing and chopping of the last few balls.

PSP here are some settings that may help you and are for PSP only.

Dwell 9.0-10.0 ms
Eye delay 5
Eye sensitivity 15
Bolt Delay 8ms
FSDO time disabled
FODO 1.0ms

Try these out and see if that helps.

Eric

[noonagon]

Thanks for the help with the settings. I'll try it out saturday!

Originally Posted by SHOOTNPOO

The 10 case rule is a great way to know your marker has done its best to get seated in with the Orings and such.

As for the settings on the HPR, you can do it either way but recommend Gases up.
1 turn out on HPR
Adjust LPR to chrono at desired FPS.

Now with the marker being broken in you can start tuning the dwell down to give yourself a more consistent shot and better efficiency.

Now the Breaking paint of the Last 2-4 balls in the hopper is in the Timing of the marker and having no pressure on the stack of paint.
Timing meaning (dwell) you need to adjust the dwell to when you are firing over the chrono you are getting better consistency in FPS. if you go to low on the dwell it will be jumping all over the place on the chrono. It will also help with the timing and chopping of the last few balls.

PSP here are some settings that may help you and are for PSP only.

Dwell 9.0-10.0 ms
Eye delay 5
Eye sensitivity 15
Bolt Delay 8ms
FSDO time disabled
FODO 1.0ms

Try these out and see if that helps.

Eric

[amossbur]

Ok, so i've had a Creed ever since they came out. I think I actually bought the first one, and the actual prototype was sent to me. I've had a few since them and will never go back.

I'm having some trouble at the moment though. I've done this a thousand times, but the other night I took her apart and replaced all o-rings, cleaned, lubed and put everything back together. Trouble is.....I can't get it to chrono past 219. I gassed her up, the HPR is about 1.25 turns out and the LPR is flush. If I turn the HPR any more out, I get a leak from between the grip frame and ram. No matter what I do with the HPR, it does not chrono over 219.

This has never happened to me before. Any help?

[SHOOTNPOO]

ok go over exactly what you replaced. It may be an undersized oring or over sized oring. As you know as well as I do some look the same size. When you say you replaced everything what exactly did you replace.
Inner valve Orings complete, LPR complete, HPR complete.
as it sounds as you may have nicked the LPR body orings and a piece of the oring is in the vented passage of the transfer tube. Pull the LPR out and check the little hole to the inside of the body make sure a piece of oring is not suck in their.

Eric

[amossbur]

I'll look back over them tonight. I'm pretty certain that the o-rings are correct. I did put in the new LPR peice.

I'll be back with my findings......

[griffan2]

i just bought the lpr upgrade, i saw that it would lower the internal pressure of the gun, i have an adjustable reg on my tank so would it help to turn down the pressure? and if so what would you recommend setting it to? when i get them in i will have the new ram, lpr, and popit in the gun.

[SHOOTNPOO]

I would keep the same inlet pressure.
If you do decide to turn down the inlet pressure I would not go below 600

[Oc_rage (Banned)]

does aaron from luckpb work for you guys now? i noticed you guys are using his barrel design. glad its back in production, best barrel concept ever.

[SHOOTNPOO]

No he does not.

[Oc_rage (Banned)]

oh so did he sell/give you guys the design to his barrel? or did you guys just copy his exact design down to the milling? or where you guys the investors that ****ed him over?

just a question, because i really do like those barrels and would shoot one again if i had a chance.