Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 10-30-2010, 07:22 PM #400
pbLanzy
Triple Stacked
 
pbLanzy's Avatar
 
Join Date: Feb 2008
Location: Irvine
pbLanzy owns a Planet Eclipse Ego
pbLanzy owns a Planet Eclipse Lv1
pbLanzy supports DLX Technology
every practice ive had a problem with my creed. This time a consistent leak was toward the middle popit o ring maybe? im having bad luck with my creed going down every time i play with it. :[
pbLanzy is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 10-30-2010, 09:56 PM #401
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Quote:
Originally Posted by p-baller100 View Post
Quick Question, I wanted to know your recommendations for lube and also where you would put oil and grease. So far I've been using vanguard's oil for everything except the hpr where I used dow 33 and I believe I used a little dow 33 on the lpr. But what are your recommendations.
Vasoline works great with the Creed.
We use a patrolium for assembly and Tech.
But the Dow and the standard marker oil is fine.

Eric
SHOOTNPOO is offline   Reply With Quote
Old 10-30-2010, 10:01 PM #402
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Red face

Quote:
Originally Posted by pbLanzy View Post
every practice ive had a problem with my creed. This time a consistent leak was toward the middle popit o ring maybe? im having bad luck with my creed going down every time i play with it. :[
It sounds like the same senario I have been hearing with markers being sold and serviced from the location you bought and have has service done.

If you are local to Long Beach bring me your marker as I will look at it personally to see where the issue may lye.

Eric
SHOOTNPOO is offline   Reply With Quote
Old 10-30-2010, 11:50 PM #403
pbLanzy
Triple Stacked
 
pbLanzy's Avatar
 
Join Date: Feb 2008
Location: Irvine
pbLanzy owns a Planet Eclipse Ego
pbLanzy owns a Planet Eclipse Lv1
pbLanzy supports DLX Technology
i looked at the board and a green wire is cut.. now the eyes will not work how do i go about getting a new board or wires?
pbLanzy is offline   Reply With Quote
Old 10-31-2010, 12:19 AM #404
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Quote:
Originally Posted by pbLanzy View Post
i looked at the board and a green wire is cut.. now the eyes will not work how do i go about getting a new board or wires?
WWW.Aggressivesports.net

http://stores.aggressivesportsdistri...yes/Detail.bok
SHOOTNPOO is offline   Reply With Quote
Old 11-05-2010, 01:39 PM #405
surge101
word
 
Join Date: Mar 2007
Location: South Florida
surge101 supports Team VICIOUS
I was wondering what the regular maintenance for the Creed is? Also what lubes should I use? I currently have Dow33 and white petroleum.
surge101 is offline   Reply With Quote
Old 11-05-2010, 03:45 PM #406
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
You can use the gun oil that is supplied or the vasoline.
SHOOTNPOO is offline   Reply With Quote
Old 11-06-2010, 10:05 PM #407
griffan2
Parabolic Paintball
 
griffan2's Avatar
 
Join Date: Jun 2010
Location: Citrus Heights Ca
Annual Supporting Member
griffan2 is Legendary
as soon as i opened the box i was excited, then i picked up the gun, the trigger is not moving freely at all, it feels like its dragging against the sided of the frame and some times it wont go all the way back to the original position. what do i do about this? and the grips are torn on the inside, the bottom of the grip is hanging off a bit so i took the screw out and it looks like its been over tightened and the screw tore through.
griffan2 is offline   Reply With Quote
Old 11-06-2010, 10:45 PM #408
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Answered in your posted thread
SHOOTNPOO is offline   Reply With Quote
Old 11-15-2010, 12:52 PM #409
wipings4urass
 
 
wipings4urass's Avatar
 
Join Date: Apr 2008
Location: Long Island
i have a v1 creed. It has under a pod of paint through it. Its basically brand new because the week i got the gun i broke my arm and had to stop playing, but now that I want to start again I realized a v2 has been released. the portable charger hasn't even had batteries in it. Is there anyway to make it v2 or send it back in?
__________________
SUPERMAN
SEXIEST HK Victory
wipings4urass is offline   Reply With Quote
Old 11-15-2010, 08:09 PM #410
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Please contact me Via PM

We do not offer parts for the V1 markers any more nor do we sell them anylonger.

Please contact me to see what we can do for you.

Eric
Vanguard US
SHOOTNPOO is offline   Reply With Quote
Old 11-18-2010, 01:09 PM #411
wipings4urass
 
 
wipings4urass's Avatar
 
Join Date: Apr 2008
Location: Long Island
pm'd
__________________
SUPERMAN
SEXIEST HK Victory
wipings4urass is offline   Reply With Quote
Old 11-18-2010, 10:58 PM #412
p-baller100
 
 
p-baller100's Avatar
 
Join Date: Jun 2007
Location: Texas
p-baller100 owns a Planet Eclipse Ego
So the oring inside the valve guide that the valve stem goes through, the valve body front internal oring 200-008 ni70, keeps popping out of its groove and leaking very badly. I have replaced the oring with a new one, both of the right size mind you, and it'll work for a little bit but then eventually pop half way out again. I have tried lowering my pressure considerably but still same issue. This is with the all delrin poppit not the lp one. I also applied a light coat of lube to it to see if it would help. Still going on after a few shots. Any idea what the problem is? I'm about to pop in the lp poppit, lw ram, and one of pooty's custom v2 bolts, as well as a .682 barrel over the .689 one I was using previously so the hpr and lpr pressures and dwell will drop considerably. Please let me know what I can do, I need this fixed tomorrow (I also still have a full oring build kit).
__________________
MINT SL94, Prophecy, E-Flex, 70/4500! Great Prices!


p-baller100 is offline   Reply With Quote
Old 11-18-2010, 11:09 PM #413
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Sounds like you may have either a worn valve body
Or a nick in the poppet.
What color is the valve body?
And what is the serial# of the marker.
Where did you buy it from and when?

Eric
SHOOTNPOO is offline   Reply With Quote
Old 11-18-2010, 11:11 PM #414
p-baller100
 
 
p-baller100's Avatar
 
Join Date: Jun 2007
Location: Texas
p-baller100 owns a Planet Eclipse Ego
Quote:
Originally Posted by SHOOTNPOO View Post
Sounds like you may have either a worn valve body
Or a nick in the poppet.
What color is the valve body?
And what is the serial# of the marker.
Where did you buy it from and when?

Eric
Got it used bout two months ago. It is black. Maybe, I didn't check the poppit. I hope it's not a valve body I need to play with it Saturday morning! haha. Serial number is 001-00076. It's got 15,000 on it according to the board. I've put maybe 1,000 through it. Oh and the rubber pad on the back came halfway off
__________________
MINT SL94, Prophecy, E-Flex, 70/4500! Great Prices!



Last edited by p-baller100 : 11-18-2010 at 11:17 PM.
p-baller100 is offline   Reply With Quote
Old 11-19-2010, 12:07 AM #415
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
IT Sounds like the Valve body is Worn if the Oring keeps coming out.
I recommend that you replace the Valve body.
SHOOTNPOO is offline   Reply With Quote
Old 11-19-2010, 12:11 AM #416
p-baller100
 
 
p-baller100's Avatar
 
Join Date: Jun 2007
Location: Texas
p-baller100 owns a Planet Eclipse Ego
Quote:
Originally Posted by SHOOTNPOO View Post
IT Sounds like the Valve body is Worn if the Oring keeps coming out.
I recommend that you replace the Valve body.
Crap. On your website it only has the valve body with the poppit combination. Can I get only the body since I've got the poppit coming in already? Any temporary fixes?
__________________
MINT SL94, Prophecy, E-Flex, 70/4500! Great Prices!


p-baller100 is offline   Reply With Quote
Old 11-19-2010, 01:47 AM #417
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
No temp fix sorry. Their is no way to make the oring stay inside the valve if it keeps coming out.

Pm me to get going in valve body
SHOOTNPOO is offline   Reply With Quote
Old 11-19-2010, 09:15 AM #418
p-baller100
 
 
p-baller100's Avatar
 
Join Date: Jun 2007
Location: Texas
p-baller100 owns a Planet Eclipse Ego
Alrighty. I probably won't get one till next week unless I can get it by 7:00 AM tomorrow haha. I think I'm going to maybe just put some locktite in there to see if it'll last me tomorrow since it's basically trashed anyways. I'll look at it again though to see if it could be anything else. Crap the screw that holds onto the valve assembly with the 1/64 head I believe is stripped at the head meaning my Allen key will not fit and the next size up is too big. I'm having no luck with my creed haha. Last time it was the same oring problem so this'll be the second time it won't work on a days play guess I shoulda checked it sooner to make sure it was fixed.
__________________
MINT SL94, Prophecy, E-Flex, 70/4500! Great Prices!


p-baller100 is offline   Reply With Quote
Old 11-19-2010, 12:37 PM #419
SHOOTNPOO
MACDEV MASTER US TECH
 
SHOOTNPOO's Avatar
 
Join Date: Mar 2008
SHOOTNPOO works for a Paintball manufacturer
SHOOTNPOO plays in the USPL
SHOOTNPOO posts videos on PbNation
Ok, sorry can't be more of a help in that.
When you are in need of the Valve LMK as we will vet you sorted out.

Eric
SHOOTNPOO is offline   Reply With Quote
Old 11-19-2010, 09:42 PM #420
twinkie69
Point Blank
 
twinkie69's Avatar
 
Join Date: Jun 2001
Location: Conway AR
twinkie69 is a founding member
 has been a member for 10 years
twinkie69 donated to help Peyton Trent
Gun is leaking out the ram cap, and I was trying to take it apart to check the ram sail o-ring, but I cant get the ram out. I watched the video and tried to pop it out with an allen key but it wont budge. Im not missing any set screws holding it in am I?
__________________
Paintball Arkansas
WANT FREE PAINTBALL GEAR???
Your Best Pick In Paintball Gear!
"SPOONS MAKE PEOPLE FAT IN THE SAME WAY GUNS KILL PEOPLE."
twinkie69 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump