Victory Tuning Guide

EthanK. · 05-12-2011, 06:50 AM

Here's a good one. While at an event, I was laying paint down and my marker went full auto for a good 5 seconds without me pulling the trigger. Anyone know what that would cause that?

Thanks.

Tz DomeCity · 05-12-2011, 03:51 PM

Quote:

Originally Posted by EthanK.

Here's a good one. While at an event, I was laying paint down and my marker went full auto for a good 5 seconds without me pulling the trigger. Anyone know what that would cause that?

Thanks.

Your trigger. Turn up your debounce. I had the same problem. I just adjusted my trigger and upped my debounce and it went away.

JimmieP.Ball · 07-17-2011, 05:43 PM

does anyone know what dwell its suposed tobe at?

gamer565 · 07-17-2011, 06:24 PM

Quote:

Originally Posted by JimmieP.Ball

does anyone know what dwell its suposed tobe at?

Yep.

http://www.tadaotechnologies.com/dow..._10_Manual.pdf

saunders182 · 07-24-2011, 01:23 PM

Ok just a quick question on some tinkering things. Is it ok to run your dwell from 6-8 ? I know alot of people have been running them at 6 but every marker is different. My G6R runs off of 6 instead of some other guys who run off 5. Any thoughts or any serious problems that might rise to running my dwell at 7 instead of 6?

DrHeLpErZx · 07-25-2011, 10:25 AM

Quote:

Originally Posted by saunders182

Ok just a quick question on some tinkering things. Is it ok to run your dwell from 6-8 ? I know alot of people have been running them at 6 but every marker is different. My G6R runs off of 6 instead of some other guys who run off 5. Any thoughts or any serious problems that might rise to running my dwell at 7 instead of 6?

Nah, changing your dwell by 1 ms won't hurt it, you'll actually get a smoother shot at the sacrifice of a little bit efficiency. But I turn mine up a ms or two when it gets crap balls cold.

kwoodStLo8(Mw) · 10-18-2011, 05:53 PM

My vics been shootin low for a while now. I put my pressure tester in a few mins ago my hpr-205 my lpr-80 I have my dwell set on 6. The balls are pretty much rolling out of the barrel.... ugh what to do?

pb_kona · 11-03-2011, 09:46 PM

If you have a slp reg, what should the pressures be at?

gamer565 · 11-03-2011, 09:50 PM

Quote:

Originally Posted by pb_kona

If you have a slp reg, what should the pressures be at?

Same as they were before.

Ty29 · 11-03-2011, 11:16 PM

Quote:

Originally Posted by pb_kona

If you have a slp reg, what should the pressures be at?

Here.

synysterballa08 · 02-18-2012, 11:59 PM

Ok so i bought a vic the other day and went to use it and now it doesnt cycle all the eay through. And the pressure tester is read 80/190. Any help?

jewstin · 02-23-2012, 01:47 AM

change up the o rings see if that helps

hawaiianbadboi808 · 03-09-2012, 04:08 AM

Question....In the manual it says to use blue loctite to set the lpr adjustment screw once its set to keep it from moving. Does that mean i have to unscrew the whole screw and put loctite or put loctite while the screw is at the set position. I've done the latter with trigger set screws before and had the toughest time removing them after. Ended up stripping the hex screw?

P4Posse · 03-17-2012, 07:44 PM

Here is a question for you. Bought a sweet v2 off pbNation. Shot it last weekend at practice was awesome. Today it wouldn't turn on properly just had green light. Wouldn't fire. Changed new battery same thing. Removed the trigger frame from the body. All in order no pitched wires or hoses. Put back together shot half a hopper and it stopped again. It is supercharged. Set up at 70/200 currently.
Board?
Noid?
User?
All the above?

gamer565 · 03-17-2012, 07:55 PM

Your getting into programming mode.

Make sure your trigger isn't holding down the microswitch. Then set your trigger up properly.

P4Posse · 03-17-2012, 08:39 PM

The green light is blue again like normal. When I pull the trigger it flashes like it SHOULD shoot but their is no burst of air. I can hear the gun gas up and if I slide the pressure tester in it shows proper pressure so it's getting air just not firing.

P4Posse · 03-19-2012, 12:03 AM

Found it. There is a tiny piece of bare wire showing. Apparently it was just barely pinching the wire. Only found it cause it started work as I was taking the grip off. Then found it works great as long as the rear screw wasn't tight. So figured it was inside somewhere and pfff found.
Thanks for your help!

pttlwin · 04-15-2012, 11:13 AM

Hey Guys

just got a v2 vic off nation and i kinda found some wear on the poppet. Just want to know if this is usual or something I need to worry about? Should I call bob long and ask about replacement?

herk8240 · 04-15-2012, 09:19 PM

That's your blast guide. I've never seen that before. Just call BLAST Monday

gamer565 · 04-15-2012, 09:25 PM

Probably just where the spring has been rubbing against it.

Shouldn't be nothing to worry about.

PinoyPaintballer64 · 04-22-2012, 06:06 PM

ok, so im fixing my friends ripper victory. today at practice it was shooting 200-260fps when i looked at it. he was shooting with a high pressure tank so i told him that was a no no and i gave him my slp to use.
after putting the slp on it shot consistently, about +-5 around 230
he tried to up the pressures messing with both the lpr and the hpr and nothing worked.
i've followed the steps with adjusting the gun without a pressure tester and that still didnt work. upon looking at his settings i found that his dwell was at 25ms!

(it has a virture board in it, not that that has to do anything with the dwell. but maybe it does? haha)
im thinking the solenoid might have pooped out cause of that, but if anyone has any remedies i could try i'd be very appreciative.