Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 06-23-2008, 06:22 PM #1
bcam9
 
 
bcam9's Avatar
 
Join Date: Sep 2007
Location: ToRoNtO, CaNaDa
couple questions

ok just got my marq
when i try to check what its capped at for bps by turn dipswitch 3 on then turn on board which is spose to make it flash current pbs. it never stops blinking, does that mean uncapped? and does it flash the actual bps or the number of trigger clicks you used to set it

this means when i try to set the cap for bps (before you set it it flashes current cap bps)i cant do it because it never stops flashing the current bps

for the above i am referring to the frenzy manual off bob's site

also on the frenzy manual it says to cap at 15 bps you have to turn dipswitch 3 on, hold down trigger until led turns white, then it will flash current bps, then you program bps with trigger pulls(5 for 15). but in the quick start guide on here it says just to turn dipswitch 3 on to cap at 15. which is the correct way?

also what do the two screws on the trigger do?

for the gear drive asa how many turns would you suggest to get good flow

and other than the fact that i am 99% sure it is, is dow33 ok to use although i know dow55 is better?

thanks alot
bcam9 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 06-23-2008, 06:27 PM #2
IgnoranceInABag
 
 
IgnoranceInABag's Avatar
 
Join Date: Sep 2007
Annual Supporting Member
IgnoranceInABag plays in the PSP
IgnoranceInABag plays in the APPA D2 division
i dont know about the first one, but the quick start guide is for the stock board, not the 3.0.

the top screw on the stock trigger is the activation point.(the pin that hits the microswitch and makes the gun shoot) the bottom one is the post travel screw( it stops the trigger from moving further)

i do not own a gear drive so i cant help you

dow 33 is fine but i would reccomend picking up some 55, it is fairly cheap so i dont think you are using 33 just because you cant afford to buy more lube..
__________________
IgnoranceInABag is offline   Reply With Quote
Old 06-23-2008, 07:13 PM #3
bcam9
 
 
bcam9's Avatar
 
Join Date: Sep 2007
Location: ToRoNtO, CaNaDa
it says the stock board is the 3.0

http://www.boblongdirect.com/index.p...48&Itemi d=62

if not what is the stock borad and where can i get the manual
bcam9 is offline   Reply With Quote
Old 06-24-2008, 02:12 AM #4
OrionOmen (Banned)
Evil Omen- My First Gun
 
Join Date: May 2008
Did you get your Marq from BobLongDirect? Your board might not be updated yet. You can send them in to get the latest updates if I'm correct.
OrionOmen is offline   Reply With Quote
Old 06-24-2008, 02:00 PM #5
bcam9
 
 
bcam9's Avatar
 
Join Date: Sep 2007
Location: ToRoNtO, CaNaDa
I did not get my gun from bob long direct it is most likely not updated. Which manual would i use then?
bcam9 is offline   Reply With Quote
Old 06-24-2008, 02:16 PM #6
OrionOmen (Banned)
Evil Omen- My First Gun
 
Join Date: May 2008
The quick start manual. Or you could send your board in to get updated. I got a non updated board as well. I bought a Yakuza though.

Link to the quick start- http://www.pbnation.com/showthread.php?t=1754673
OrionOmen is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump