put in the orange bolt and it only shoots like 5 ft now??

k-ospaintball.capt. · 10-29-2007, 12:47 PM

so... i just got an orange bolt for my mini and put it in and it only shoots the balls out like 5 ft... i turned up the dwell and that deffinetly didnt help.. any ideas??

THE_INCREDIBLE_BULK · 10-29-2007, 12:52 PM

Orings. Try the different bolt guide orings.

coolicarboy · 10-29-2007, 02:00 PM

Did you try and raise your velocity? Also check your pressure and see if its at 200.

Destined-Glory · 10-29-2007, 03:14 PM

do you have the new orings in? If not then you need to do that, and raise the dwell to like 32-34.

Bakermancan · 10-29-2007, 05:02 PM

I found If you use shocker bolt guide o-rings they work MUCH better.
The supplied o-rings from orange make a ton of friction and the shocker ones are smooth yet not too small and I could hit the same velocities without raising dwell.

ActiveShooter · 10-29-2007, 05:08 PM

Use the orings that came with it and make sure you use a ton of lube. Also dry fire it to seat everything in. It will work fine in no time.

Ego_Beater · 10-29-2007, 05:55 PM

Does anyone know where to buy one thats in-stock? Check your velocity adjuster and change the o-ring sizes.

jackh70 · 10-29-2007, 06:54 PM

Where I got mine. And it's in stock!

I just put mine in for the first time yesterday and shot about 1/2 case through it. I tried it first with the stock o-rings because the ones that came with it just seemed too tight. Didn't have much luck! Velocity was all over the place and chopped several balls. I put the supplied o-rings in and lubed the pee out of them. Works like a champ!! Velocity was +/- 5. We'll see how effecient it is this weekend.

evil35 · 10-30-2007, 08:27 AM

I'm having the same problem.changed out o-rings which seemed to small.I have the tadao board so the dwell only goes up to 20.I used 9 as my starting point.made some changes +/= no change.All i'm getting is chop chop chop and a big mess.The guns new to me so i'll keep checking back thks.

MaxOC · 10-30-2007, 08:39 AM

Quote:

Originally Posted by evil35

I'm having the same problem.changed out o-rings which seemed to small.I have the tadao board so the dwell only goes up to 20.I used 9 as my starting point.made some changes +/= no change.All i'm getting is chop chop chop and a big mess.The guns new to me so i'll keep checking back thks.

use the supplied o rings. o and btw on the tadao board the dwell is 1 ms a setting. instead of 1/4 ms a setting like on stock

evil35 · 10-30-2007, 09:09 AM

I don't mean to sound like a tard but i'm not sure i'm following you. So the m/s 1 instead of 1/4 on stock board i get that.I don't have the tadao baord sheet in front of me so the ( 0 and btw is ? and what is a good starting point ) thks for you time.

MaxOC · 10-30-2007, 09:17 AM

Quote:

Originally Posted by evil35

I don't mean to sound like a tard but i'm not sure i'm following you. So the m/s 1 instead of 1/4 on stock board i get that.I don't have the tadao baord sheet in front of me so the ( 0 and btw is ? and what is a good starting point ) thks for you time.

on the tadao board each blink of dwell is 1 ms. on the stocker each blink is 1/4 ms

evil35 · 10-30-2007, 09:54 AM

ok. i understand that part.but what's a good starting point.what's causing the chopping? is the dwell to high or low.or is there another setting that i need to ajust.Do you have these kind of problems when setting your's up. what was your settings on stock board. just trying to get starting point thks