Black V2, ram wont slide out the back - PbNation
Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

 
Archived Thread - Cannot Edit  
Old 04-20-2007, 01:16 AM #1
Tequila_sunrise_trix
 
 
Join Date: Sep 2004
Location: DFW
Black V2, ram wont slide out the back

I just recieved my black v2, played with it once, went to pull the ram to clean and it won't come out the back like in every pic or vid I have seen. What gives?
__________________
My feedback
Tequila_sunrise_trix is offline  
Old Sponsored Links Remove Advertisement
Advertisement
Old 04-20-2007, 01:41 AM #2
VS_001
 
 
Join Date: Jun 2006
Location: Finland
Check that little groove that holds ramcap in its place. Ball bearing may have hammered little burr in the end of it.

You should cut or grind off this little burr and check that ball bearing is tightened correctly. there should be quite snug fit, when you replace or remove your ramcap. Be careful tho. It's easy to overtighten the ball bearing and ruin your ramcap. Tighten just a bit and test. Repeat this until it's hard to twist the cap.

When your cap fits snugly in it's place, it wont hammer it's groove and ramcap wont fall off during gameplay.
__________________
Paranoia - Finland
VS_001 is offline  
Old 04-20-2007, 08:07 AM #3
Arstron
fusionowners.org
 
Arstron's Avatar
 
Join Date: Jul 2005
Location: missouri
Let me state the obvious first, you did pull the bolt pin didnt you?
__________________
Fusion Owners preview
Current Markers: DP: Fusion, G3, Threshold, Revi, and G5
AGD: 2xEmags, 1 RT Pro, 1 Classic, 1 Aluminium Classic R/T, 1 Pump Mini Mag
For Sale: Carter Custom Mini Comp - Tequila Fade Emag
WTB your broken DP markers.
Arstron is offline  
Old 04-20-2007, 12:08 PM #4
Tequila_sunrise_trix
 
 
Join Date: Sep 2004
Location: DFW
Yes, I pulled the bolt pin. There is no bur in the ram sleeve area where the cap goes on. I don't want to force it, and I don't want to pull the valve to pull the ram out of the front.
__________________
My feedback
Tequila_sunrise_trix is offline  
Old 04-20-2007, 12:45 PM #5
IntenseImage
Death Dealer
 
IntenseImage's Avatar
 
Join Date: Jan 2005
Location: Northampton, PA
IntenseImage is playing at Living Legends III
Grab the thin end of the ram and wiggle it out. The ball bearing does flare its channel a bit (you may not even notice it) and once you get the ram out it smooths back down. Then it should go in/out easily.

Trust us on this one
__________________
IntenseImage is offline  
Old 04-20-2007, 04:24 PM #6
savini72
 
 
savini72's Avatar
 
Join Date: Jul 2006
smae thing happens to me. i just like turn my marker up side down and hope it falls out. haha works after 2 or 3 trys!
__________________
HurricanesSupporter#247
http://www.pbnation.com/showthread.php?t=1823138
^^^^feed back 15+/0- old, 4+/0- NEW[/center]
savini72 is offline  
Old 04-20-2007, 05:42 PM #7
assassinationACI
ONCE GREAT, ALWAYS GREAT
 
assassinationACI's Avatar
 
Join Date: Jul 2005
Location: GOOSECREEK, SC
assassinationACI is a Supporting Member
use the bolt pin to push it out, pull the bolt pin out, then push it back in above the ram, not in the slot and push back.
__________________
OLD feedback
assassinationACI is offline  
Old 04-20-2007, 05:46 PM #8
RevBubba
The Bub Abides
 
Join Date: Mar 2002
Location: Canada
RevBubba is a Supporting Member
 has been a member for 10 years
^^^
Yup that will work!
__________________
I remain,
The Reverend Bubba


"Most men lead lives of quiet desperation"..... but I can still hear their screams.
RevBubba is offline  
Old 04-20-2007, 06:10 PM #9
FDS. (Banned)
yes im a kool kid
 
Join Date: Mar 2007
Location: Monterey CA 831
my second one did this, its really nothing to be woried about just a little inconviente
FDS. is offline  
 




Posting Rules
Forum Jump