milled the TES!

motoman13 · 01-14-2007, 11:22 PM

i got bored so i decided to do alittle milling. i think i might have cut a little to far on the half back but o well il just make a delrin bolt for it when i get the chance. there is still alot of work left but just gona post some pictures of it now. any sugestions???

rjones1213 · 01-14-2007, 11:58 PM

i think it's so square on the sides and i'm not really sure if the bottom tube is going to work
other than that it looks good but you should round it out and take off all of the green anno.
what did you use?

XxAltecxX · 01-15-2007, 06:50 AM

Eh, little worried about that top-tube window. Its right over the air passage. I can see that giving very bad blow-by. Other then that, and the bottom window needing to be longer, it looks good.

motoman13 · 01-15-2007, 11:23 AM

k il try work that stuff out. i forgot all about the eye and stuff so idk how that will be affected but then again my eye doesnt work so owell. i used a milling machine. i think i might take the little ridge thingies on the top of the body too

Agitator · 01-15-2007, 01:28 PM

Quote:

Originally Posted by XxAltecxX

Eh, little worried about that top-tube window. Its right over the air passage. I can see that giving very bad blow-by. Other then that, and the bottom window needing to be longer, it looks good.

yeah- the top tube window may=trouble

altec- he can't make the bottom window much bigger... tes....

nice lookin' work

Dragun_paint · 01-15-2007, 02:25 PM

man if i had your tools, i'd go crazy on my guns, too bad i don't have any milling tools, its hard to do precise milling with a dremel and make it look that smooth, wait till i get a job, imma get a hold of an ego frame and ego frame my t1....jus wait fellas, i need some money!!! so if any one wants to donate me some :dogdy: aha, anyways looks nice moto

foughtwolf · 01-15-2007, 02:29 PM

watch the top tube windows, I'm not in the know about the TES/yours,, but if its cut to much the window will chew upthe front o-rings if they have any.

Rockfrog · 01-15-2007, 02:50 PM

I think that'll be a small issue compared to the one 'tator and altec mentioned. the top tube window is above the valve vent, a tight fitting delrin bolt will be needed to operate ... the windows is between the points any o-rings would be during firing so would not do any real sealing and thus vent more than a close fit delrin bolt would. perhaps cutting an o-ring channel around the bolt hole and super gluing an o-ring in that way would allow sealing, but durabiltiy would be a question. in theory it would work, but, sadly I think you just lunched a body. But it looks great though.

you could possibly sleeve that portion of the body ... over bore the top tube just past the window and slip in a lexan (or something of the sort) tube, bored to size, to allow proper sealing.
just ideas.

motoman13 · 01-15-2007, 03:24 PM

heres some more pictures. im not realy worried about how it opperates right now because i never use it anymore and when ever i try to something always breaks LOL. but here are the pictures

Rockfrog · 01-15-2007, 03:35 PM

I LIKE!
does the end cap still have an adjustment or is it just a cap.
Honstly you should get it to work properly ... try it it might work without problems ... maybe a groove in the bolt between th o-rings on either side just below the window, cut and glue a piece of an o-ring in there and it should seal fine. it would be sweet to get it working.

motoman13 · 01-15-2007, 03:46 PM

k i will. but i need to get a lpr and a hpr for my drallion first, my freind needs thows befor he goes and tunes that all up for me.

Dead_Bunny · 01-15-2007, 05:18 PM

sweet gat man, does it shoot pretty well?
I have been wondering how well a lower window would look on a TES.
Hahaha, if it isnt too much trouble could you get a pic of it with the bolt cocked??

motoman13 · 01-15-2007, 07:47 PM

Dragun_paint · 01-15-2007, 08:05 PM

did you make that bolt? or what? looks nice to bad it might have a little bit of issues to operate.

motoman13 · 01-15-2007, 08:20 PM

ya i made that bolt, it isnt quite finish i got alittle more work to do to it.

Dead_Bunny · 01-15-2007, 09:43 PM

compleat metal?? whew if so that is one heavy son of a gun lol

Agitator · 01-15-2007, 10:22 PM

GAWD!

That thing's pretty freakin' hawt! I'm an envious tator. I don't envy the problems you'll have with that window, but that thing's sick.
If you fasor'd it to slow the bolt down, it'd look super-hawt every time you'd shoot!

Dragun_paint · 01-16-2007, 11:05 AM

man i might have you make me some parts...later on, so keep an eye out for me dude.

Rockfrog · 01-16-2007, 12:01 PM

give it a wasp waist, angle the inlet some, taper the end and leave as much thickness at the sealing area as allowable to still continue function and it may solve some of your problems ... you'll most likely still get some blowby (maybe not, you'll find out when you test it) ... but it's gonna look killer hawt!

Agitator · 01-16-2007, 12:30 PM

It looks like you could remove a lot more material from the rear portion of the gat. through the window in the bottom, I can see that it's quite thick.

Dead_Bunny · 01-16-2007, 03:44 PM

mmm eye's from tator+ milling from motoman= the awesome'ness

lol then again thats only if moto man would start milling people's gats...
*hint hint*