Official MARQ Troubleshooting/Known Issues...

96 Ls lnteg · 10-31-2006, 11:58 PM

Quote:

Originally Posted by pattypat808

also another problem i found is the hedlock just brakes right into the loaders neck anyone else had this problem>>> and any suggestions hopefully they make a new hedlock for this gun soon....

Huh?

the incubus · 11-01-2006, 12:10 AM

Well this is a problem that has mainly been a factor with Hybrid Shells. For some reason they are more brittle than Halo or Empire shells and I believe Hybrid is in the midst of switching to a higher quality/more forgiving plastic.

I'm sure it may have happened on Halo or Empire shells but to my knowledge those are few & far in between.

And B'sides... he feednecks already go on bloddy tight as is so the Headlock as you call it should only be torqued down a smidge to ensure it wont fall out so ease up a bit. This is afterall Plastic going up against Metal.

orbitaldeath3 · 11-03-2006, 07:00 AM

So from what ive read so far, does anyone use a reloader B or halo on their onyx without any problems whatsoever? Or has everyone with a halo or reloader experienced a few problems

4thDegree · 11-03-2006, 07:02 AM

96 LS Integra is running a Halo with the Angry board and he reports no problems.

orbitaldeath3 · 11-03-2006, 07:08 AM

Quote:

Originally Posted by 4thDegree

96 LS Integra is running a Halo with the Angry board and he reports no problems.

That i heard but i want to know if anyones running a stock reloader B of somesorts. im getting a reloader in a trade and i wanted to stick a pair of sucuide shells on it since i do like reloaders more then vlocities. I dont know why, its just personal but if i HAVE to use a vlocity then oh well

TeamShellShock · 11-03-2006, 07:13 AM

I use a Halo on mine. no problems with that.

I did have an oring issue but it was easily solved

96 Ls lnteg · 11-03-2006, 07:51 AM

Quote:

Originally Posted by orbitaldeath3

That i heard but i want to know if anyones running a stock reloader B of somesorts. im getting a reloader in a trade and i wanted to stick a pair of sucuide shells on it since i do like reloaders more then vlocities. I dont know why, its just personal but if i HAVE to use a vlocity then oh well

Here a vid with a reloader...

http://www.motherfinmike.com/videos/onyxvid.wmv

4thDegree · 11-03-2006, 09:28 AM

I am running a reloader b on mine. I had to do a bit of adjusting with the LPR but it is working well now. I have just have had it recommended to me that the Vlocity seems to work the best due to lower pressure on the ball stack.

the incubus · 11-03-2006, 11:22 AM

Quote:

Originally Posted by orbitaldeath3

So from what ive read so far, does anyone use a reloader B or halo on their onyx without any problems whatsoever? Or has everyone with a halo or reloader experienced a few problems

I too run a stock Halo (Never had reason to change a thing) and no issues yet.

squeek22 · 11-03-2006, 12:31 PM

i sent my onyx back to blast bcs there was a prob wiht my bolt, there was a sharp edge causing it to chop paint. they also said, when i talked to them on the phone, that they put a HPR schrader valve in the gun. what exacly is this and what does it do?

also my gun seems to run away when its on ramp, is there anyway to stop this with out putting the spring back in? i honestly donot like the feel of the spring and like the trigger much much more with out it

96 Ls lnteg · 11-03-2006, 01:41 PM

Quote:

Originally Posted by squeek22

i sent my onyx back to blast bcs there was a prob wiht my bolt, there was a sharp edge causing it to chop paint. they also said, when i talked to them on the phone, that they put a

Odd I never heard of that before

HPR schrader valve in the gun. what exacly is this and what does it do?
when you take you torpedo apart an you see that pin on the upper half of the torpedo its just changes that you can use both HP & LP air systems

also my gun seems to run away when its on ramp, is there anyway to stop this with out putting the spring back in? i honestly donot like the feel of the spring and like the trigger much much more with out it
You can either set your dipswitch for debounce on high, an see if that cure the issue or you can change you activation point your trigger or you can do the magnet mod on the trigger

There you go

squeek22 · 11-03-2006, 04:22 PM

the only way i could make it stop going full auto was i had to put a pen spring that makes the trigger stiff as hell. i put the dbounce setting (dipswitch 2) to on (maximum setting) still runs away, i tried adjusting the activation points but the screw wont move. the allen key that fits it like catches and then spins (like its to small) but one bigger doesnt fit. i dont think its stripped...now my trigger is horrible lol

the incubus · 11-03-2006, 04:30 PM

Send it in to BLAST. It should not just bounce all the time. You can achieve a proper adjustment on the Trigger so it functions properly but if you can't get it to do so, BLAST can.

Call them up to set it all up.

ROB.

squeek22 · 11-03-2006, 04:48 PM

lol i jsut got my gun back today from them...kill me

4thDegree · 11-03-2006, 04:58 PM

1/16" allen wrench is what is required to adjust your trigger.

squeek22 · 11-03-2006, 05:11 PM

thats what i was using

wakaya · 11-03-2006, 10:59 PM

k veloctiys set fine , im using cold weather paint a vlocity and a stiffi 14 inch barrel and im chopping like nether before , my eyes are clean and all ...i dont understand what could be goign wrong

96 Ls lnteg · 11-03-2006, 11:01 PM

might need to lower your LPR pressure

ADOLF · 11-03-2006, 11:04 PM

detents?

wakaya · 11-03-2006, 11:38 PM

hmm how do i lower the lpr pressure on an onyx?

b1aze · 11-04-2006, 07:22 AM

Is there a way i can turn the air flow ALL the way off via the HPR? Like, unscrew the adjuster screw to flush or past that so i dont risk over pressurizing the gun upon gasup? I really dont like not using an on/off, so i have one in the mail, but i really wanna try this tomorrow and i hate not having a bleeding on/off