[hatchetwarrior1246]

I'd actually be making a hefty profit off of that. but no thanks.

[Lord_Lippie]

Originally Posted by Dyeguy05

Hey guys I need some help with my brand new victory...I got it yesterday, first hopper shoots perfect...then it shoots 3 shots then goes full auto but not good full auto they just roll out. At the same time it starts leaking like ****ing crazy!!! Then I'll take the bolt out it'll shoot a hopper fine then do it again! I checked everything and its lubed well....I had just enough air to turn up the dwell to 8 and put the gun on semi uncapped it worked for the little bit of air I had....Any advice?

Okay, I just got my Victory back from BLAST getting SC'd, it is now doing the same thing that happened to the guy I quoted, So..... I have to send it back to them and have it drilled? I'm playing PSP Phoenix, so I doubt they'll get it back to me in time... If a BLAST tech could please PM me, or answer here on what to do I'd be much abliged.

EDIT: I just talked to Terry, and he instructed me to lube the heck out of the poppet and such. I did, and by god, it works wonders now. Thanks Terry!

[pballernick]

marq 6 not getting enough air to move the bolt, only a little air gets to it when i fire and it has a tiny leak down the barrel, changed orings (large ones) and it still leaks

[gamer565]

Originally Posted by pballernick

marq 6 not getting enough air to move the bolt, only a little air gets to it when i fire and it has a tiny leak down the barrel, changed orings (large ones) and it still leaks

Whats your pressures at?

[herk8240]

Did you do anything in between it working and not? Did you take it apart to lube it? Here's the standard starting points

1. Replace battery
2. Check the rear transfer hole for o-ring chunks and your o-rings for damage
3. If you took the back cap off the engine, make sure the holes are facing down and close to center.

[pballernick]

i dont know the pressure because i dont have a tester, the baterry is fine ill check the rest

[pballernick]

oh and when i put my finger over the front of my bolt it stps it and it builds pressure then it pushed my finger off and continued to leak

[gamer565]

Originally Posted by pballernick

i dont know the pressure because i dont have a tester, the baterry is fine ill check the rest

Get a tester before you even try anything else.

[pballernick]

thanks

[DominicanPballer]

my victory is leaking from the ASA, exactly from the part where the ASA and the frame comes together. I changed the oring 3 times and still the same. Help please

[bronze]

put a new o ring in and dont lube it. then tighten the set screws in a star pattern. if your not already, use a LP output tank

[DominicanPballer]

done and still leaks :S

[bronze]

your victory have an aftermarket ano?

[DominicanPballer]

no sir! im going nuts! its stock

[xeese]

What reg do you have?

when doing the star pattern get all of the bolts snug before torquing them tighter. after snug about 1/4 turn on each one then move to the next in the star.

[bmoreballa119]

quick question... my rapper was shooting +-30 fps on sunday it started out out at 255 up to 275 down to 245 up 285 then up to almost 310 any insight on what is going on would help greatly now grant it was around 45 degrees in the morning not sure if thatll cause this but i need it more consistent obviously

[M98custom1212]

Settings?
Fresh Battery?

Check the rear air transfer hole inside the body for parts of a broken oring

[gamer565]

Originally Posted by bmoreballa119

quick question... my rapper was shooting +-30 fps on sunday it started out out at 255 up to 275 down to 245 up 285 then up to almost 310 any insight on what is going on would help greatly now grant it was around 45 degrees in the morning not sure if thatll cause this but i need it more consistent obviously

Whats settings and hpr/lpr psi?

Have you tried a new battery?

Are you underboring?

When was the last time you lubed everything?

[bmoreballa119]

battery is brand new and lubed it the night before practice and just so i know what should the lpr/hpr be at i just recieved the rapper in a trade and im kinda new with marqs but ill check it right now

[gamer565]

Originally Posted by bmoreballa119

battery is brand new and lubed it the night before practice and just so i know what should the lpr/hpr be at i just recieved the rapper in a trade and im kinda new with marqs but ill check it right now

LPR ~70psi

HPR ~200psi

Did you use dow55 when you lubed it?

[nvghostrider]

I have two leaking Marq solenoids. Anyone know were I can send them for service? Already bought two new ones but would like to have spares.