[crazykyle931]

[quote]Cut Egg paddle mod- cut away paddles to either leave a straight line(you cut four paddles, my favorite method as it actually increases bps as opposed to increasing consistancy), or a Mercedes-Bens symbol(three). Now reinforce the paddles by one of the following methods: sticking a needle down the paddle, putting straws onto the paddles, or if you have done the two paddle mod, glue a lollypop stick on top of the paddles. 2-4 bps


first off, is this method only good for the eggy 2? or can it be done for the eggy 3 also?

second which cutting method speeds up bps the most (4? 3? or straightline 2?)

[The_Lead_Factor]

Cut Egg paddle mod- cut away paddles to either leave a straight line(you cut four paddles, my favorite method as it actually increases bps as opposed to increasing consistancy), or a Mercedes-Bens symbol(three). Now reinforce the paddles by one of the following methods: sticking a needle down the paddle, putting straws onto the paddles, or if you have done the two paddle mod, glue a lollypop stick on top of the paddles. 2-4 bps


first off, is this method only good for the eggy 2? or can it be done for the eggy 3 also?

second which cutting method speeds up bps the most (4? 3? or straightline 2?)

1. They're the same thing, minus the board. So yea, it can be done to both.

2. There isn't much of a difference at all between the 2 or 3 paddle mod, do whichever you feel like doing.

[Mr Carlos]

Damn flight your the **** im not the only person who loves thier egg

[StopBANNINGmePLEASE]

Can we get this stickied??

[The_Lead_Factor]

There's a link in the sticky's... But yea, it would be better to have it as it's own sticky.

[quikest]

guys, do you know any speed feed mods?

[The_Lead_Factor]

http://www.pbnation.com/showthread.p...0#post31598700

It was on page 10 of this thread

[Outlaw.99]

Page 10 for some....Depends on how many you have set to view at a time...heh....Page 5 for some of us...

[The_Lead_Factor]

Which is why I posted up the link too, not just where to find it

[fatalorgasm]

right now my Eggy 3 is my only electro feed left so i dont wanna mess it up. I wanna try the 3 or mayb 4 way Impeller (so cut some of) but im afraid it will mess it up. I understand that this mod "works" but does it decrease bps?? increase BPS but less consistancy??? other way around?? what happens when All six are Reinforced??? I dont really care about being the Speed up i just want the end of the hopper to be better, you know when youre low on balls and it flicks them around.

[pb_freak9666]

here's my mod. pretty BA, and cheap to do.
EDIT: sorry about the bad quality, did it with my camera, plus it was so light out.

[fulleffect6912]

so i've been looking to get a new lid for my egg, then i just decided to make my own speed feed for it, but all the pictures are gone, can anyone post them up again

[ccoelnslash]

Originally Posted by fulleffect6912

so i've been looking to get a new lid for my egg, then i just decided to make my own speed feed for it, but all the pictures are gone, can anyone post them up again

same here.. i need a template.. i know the materials just need the template to cut from

[justavillain]

those measurements might not be right I think I guessed a while ago about them

[codyzy]

hey that rev propeller is way better than teh stock. it increased my bps by 4-6.

[cpufreak3]

I have a revy impeller (the one that goes out and up) for my Eggy2, but the paint keeps getting jammed under the blades.

I heated the blades and flattened them, but I'm still having the same problem.

Do I need to lower the whole impeller by sanding the axle it goes on?

[mikeplaysspeedball]

that looks realy bad

[w00ds]

Bump This Thread Is Awsome.

[longhornjake]

How about using those TechT squishy paddles that are supposed to be for the tippmann cyclone...maybe just the bottom half that's flat. I just looked at my paddles and noticed that 3-4 of them are cracked at the base. Should i just cut these off? I might have none left. Also, where do we get those other propeller that many are suggesting? From VLparts.com?

[sicandhopeless]

hey a problem i had with an egg once you might wanna throw up there is if you put your battery board back in backwards your motor will spin backwards cuz of how the current is drawn. if your servo spins backwards the balls wont feed. just a thought.

[DSchmidt54]

Hey GUys ! idk if this thread even gets read anymore but i just got done modding my evo 2 after re-wiring the damn servo,, and right now im extremely happy with the results! ive done the speedfeed, 2-paddle, feedneck, and batterydoor mods successfully and here are the results ,,,FYI the speedfeed is actually a light olive green , for some reason it looks yellow ,, and yes my hopper has fins !!

http://s871.photobucket.com/albums/a...t=DSCF4162.jpg

http://s871.photobucket.com/albums/a...t=DSCF4161.jpg