Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 04-12-2006, 03:58 PM #1
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
Arrow #5 Steps For New Wrath Users

These Five steps will help you get started with your new diablo wrath.
I was one of about a dozen of us whom first got the diablo wrath and i had no idea how to adjust it. This won't happen to you. This will work for the many 1st edition Wrath's as well as the LTD.

The Five Steps

#1.Take and place drops/globs of lube (evil pus,doww 33, liquid ice, bloo goo or extreme rage lube) in your bolt area (unless its delerin) next take and push the bolt forward a bit until you see the bronze colored ram, place a few drops/globs there as well.

#2.Now your ready to shoot aren't you? Not yet, you still need a 9v battery, then, after this you'll need to adjust your High pressure regulator and low pressure reg. The high pressure is the one with the gauge and where your hand can go, the lpr is under the barrel a bit. Turn the adjustment screw for the HPR (on the bottom) all the way out (counter-clockwise). Turn the adjustment screw fot the LPR (in the front) all the way out until even with the front of the LPR.

#3.So ya got your reg lowered, now play with your menu a bit, without your air tank in......first turn it on, then unlock it, what is your bps set at? you should adjust this dependant on what hopper your have.
Here's a quick list
Standard 200 round-10bps
Revolution9v or 12v-15bps
Halo Tsa-16bps
Egg or halo b-20bps (or more if u hav aftermarket board)(for help on boards take a gander in the FAQ)


Now if you have a R15 board adjust the debounce any where from 8-15 is a good range, mine is at 12.
Play a bit more if ya plz, click around and adjust your trigger if need be.

#4.Get out air tank/co2 tank and get ready to find a chrono. Before you place your tank in, place three or so drops in your ASA this way you can lube your reg up quicky as well as getting some to the noid. Place your air tank in, and make sure your barrel and sleeve are on.
Adjust the HPR until it reads 250-260 psi. You may want to fire a shot or two after every adjustment, while the reg is still breaking in.

#5.Now load up with paint. Remove your barrel sleeve. Shoot slowly and safely, over the chrono. Adjust your lpr as you go until you get desired velocity.

OTHER TID BITS OF HELPFUL INFO
*Lube after each time you play and follow JJ's "lazy" Wrath maintenance Found here http://www.pbnation.com/showthread.php?t=1320462

*Place electric tape around bottom of reg, near your braided line in order to not scrath the paint (happend to me).

*Use electric tape when you play in wet/damp and dirty places, wrap it around your grips in order to keep the dirt.water out of your board and noid.

*Use fresh batteries like energizer and duracell ultra. Rechargable work well for a while as well.

*When you clean your wrath run a squeege through the main body but first take out the eyes and detents by unscrewing the eye covers. It saves your detents and keeps eyes clean.

*Everytime you play put those couple drops into your asa to keep the reg lubed up.


Help From Other Wrath Owners

madman7048
Quote:
Originally Posted by madman7048
you know i have started to adjust my regs alittle different. i set my hp reg to about 325 and the lp reg to about 100. changed my dwell to 10ms. i have no more barrel breaks and my effiecency has gone up. i can now shoot about 450 balls on a 47 3000 steel tank. just goes to show that each gun is alittle different
diablowrath678
Quote:
Originally posted by diablowrath678
that happened to mine, i sent it in or you can try moving the solenoid forward

edit:

take off the frame and grip (dont want to break the eye leads)
lossen the 2 noid set screws.
slide the noid forward a bit and tighten it down. (I took mine out first when i did this but i dont think you have to and its a pain to get it back in)(not death grip tight)
turn it on, turn the sensor off
and click away. if it dont work try a new batt. or the noid may be fried you have to send it in to get it fixed

squints88
Quote:
For the delrin ram, the HPR should be running at 400psi, then do the same procedure as above to dial in the lpr. I think i heard somewhere that the lpr is actually set lower with the delrin ram, but im not sure. Hope this helps and I hope you join the legion!
Need another manual cause you lost yours?
get it here
http://www.paintballsolutions.com/05...nual_wrath.pdf

OTHER Info in other threads
Toolshed's Thread

Board info (If You have the wrath ltd go to the R15 board section, for regular wraths go to the BD 5+ section.)
BD 5+ Thread

R15 Thread
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board

Last edited by jjdustr340 : 04-25-2006 at 08:16 PM.
Toby15custom is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 04-12-2006, 04:51 PM #2
jjdustr340
My son will bunker you.
 
jjdustr340's Avatar
 
Join Date: Jan 2004
Location: Home of the Buckeyes!!
jjdustr340 is a Moderator
jjdustr340 is a Supporting Member
 has been a member for 10 years
jjdustr340 posts videos on PbNation
jjdustr340 supports our troops
jjdustr340 is one of the top 500 posters on PbNation
jjdustr340 is Legendary
Toby---
Thats a mighty fine start for some sticky material! I can think of a few things to change and add, but I'll let everyone else put in their ideas.

Let's get some input, edit the original post, and then add we'll add it to the sticky. I've been just waiting for someone to make one.
jjdustr340 is offline   Reply With Quote
Old 04-12-2006, 05:07 PM #3
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
yeaaaaa...input peoples.....plz......
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-12-2006, 05:11 PM #4
Clear_Water
 
 
Clear_Water's Avatar
 
Join Date: Dec 2005
Location: Directly Behind You
my r15 doesn't have a dwell feature, do you mean debounce?
__________________
98% of People don't know how to use numbers correctly . If you are part of the 2% that doesn't, put this in your sig.

Cancel my subscription to the resurrection
Send my credentials to the house of detention
Clear_Water is offline   Reply With Quote
Old 04-12-2006, 05:22 PM #5
diablos Remnant
shocker mafia member 139
 
diablos Remnant's Avatar
 
Join Date: Jan 2006
Location: Thorofare, NJ
nice job man


try telling them how to take the gun apart for better lubing process. or tell them how to get the the ram.
__________________
"Originally posted by ShotOnSight: Pbnation (n)- An online paintball community where at any given time one can find 75 paintball enthusiasts discussing the sport of paintball and 1500 teenagers calling eachother gay."

DEATH BEFORE DISHONOR

DO NOT DEAL WITH L.I. Careaker he scammed me out of 150 and he'll do the same to you!!
diablos Remnant is offline   Reply With Quote
Old 04-12-2006, 05:31 PM #6
rbooker
Embrace the Suck!
 
rbooker's Avatar
 
Join Date: Apr 2005
Location: Raeford
rbooker owns a Planet Eclipse Ego
rbooker plays in the APPA D4 division
I think a sticky may be in order.
__________________
Regal Ego 11
Regal Geo 2.1
rbooker is offline   Reply With Quote
Old 04-12-2006, 05:47 PM #7
jjdustr340
My son will bunker you.
 
jjdustr340's Avatar
 
Join Date: Jan 2004
Location: Home of the Buckeyes!!
jjdustr340 is a Moderator
jjdustr340 is a Supporting Member
 has been a member for 10 years
jjdustr340 posts videos on PbNation
jjdustr340 supports our troops
jjdustr340 is one of the top 500 posters on PbNation
jjdustr340 is Legendary
OK, I can't resist.....

Step 2.5---what to set the HPR and LPR at.
Anyone? Anyone? Bueller? Bueller?
jjdustr340 is offline   Reply With Quote
Old 04-12-2006, 06:44 PM #8
POP-POP
Rusty Spoons
 
POP-POP's Avatar
 
Join Date: Nov 2005
Location: Connecticut
O O O O i know !!!!

HPR set at 250 psi LPR about 1 and a half turns from flush/ till you reach the desiered (sp) velocity!


o yeaaa
__________________
I got a mother-****ing Wrath *****.

May '06 Diablo Marker of the Month

No Pain, No Game.
POP-POP is offline   Reply With Quote
Old 04-12-2006, 08:30 PM #9
madman7048
 
 
madman7048's Avatar
 
Join Date: Jan 2006
you know i have started to adjust my regs alittle different. i set my hp reg to about 325 and the lp reg to about 100. changed my dwell to 10ms. i have no more barrel breaks and my effiecency has gone up. i can now shoot about 450 balls on a 47 3000 steel tank. just goes to show that each gun is alittle different
__________________
WRATH LEGION/SILVER DIVISION/SPECIAL OPS

WHEN ALL IS FINISHED THERE WILL ONLY BE MY WRATH
madman7048 is offline   Reply With Quote
Old 04-13-2006, 01:22 AM #10
jayrad
BOB SAGGOT!!!
 
jayrad's Avatar
 
Join Date: Apr 2005
Location: G-dale, C-ville Wa
I don't think you'r hopper feed rates are right.. Can a Halo TSA feed 18bps? It's not even rated that high..

Other than that when you want to SPECIFICALLY lube the noid, just take out the LPR hose and put a drop or two in that hose, it shoots it right to the solenoid.

And don't forget to lube your nasty stock metal bolt!
__________________
TEAM DUMBFACE
jayrad is offline   Reply With Quote
Old 04-13-2006, 12:53 PM #11
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
idk my tsa is pretty fast, i can get 15bps or so with it....
good input everyone now jj and i can get ready to sticky, jj i made some adjustments and if you would be so kind as to post or shoot me a PM as to what i need to add or subtract for final posting.
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board

Last edited by Toby15custom : 04-13-2006 at 02:04 PM.
Toby15custom is offline   Reply With Quote
Old 04-13-2006, 09:25 PM #12
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
up jj anything else i need to add and get her stickied....
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-13-2006, 11:41 PM #13
a pb baller
DIABLO DESTROYS
 
a pb baller's Avatar
 
Join Date: Jan 2006
i have my debounce on 1 my shop dude set it 4 me before i picked it up he said it will allow me to shoot faster is it bad that i have it that low
i think he now what he is doing tho he plays 4 aftermath
anyone have any reson y this wold be bad
it is legal isnt it

b/c my local tournys like pevs and everthing never check
i am not trying to cheat so if it is illegal i will change it
__________________
warped sportz dark angel
ith 04 wdp speed board
twisted volumizers
boomstick
rips like ****

diablo wrath LTD mutha truka
a pb baller is offline   Reply With Quote
Old 04-14-2006, 09:02 AM #14
muppetmower316
 
 
muppetmower316's Avatar
 
Join Date: Oct 2005
Location: concord, NC
i really dont think u can get 10 bps outa a gravity fead, and you should probablly mention the ****ty eye logic with the stock board so u wouldnt be able to get 20 bps out of a z-board
__________________
my feadback
muppetmower316 is offline   Reply With Quote
Old 04-14-2006, 04:36 PM #15
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
i just put rough areas....i didn't go hard core exact...and yea the 10bps thing was just there in my head, i know a stand. could do like 4bps.
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-14-2006, 04:51 PM #16
jjdustr340
My son will bunker you.
 
jjdustr340's Avatar
 
Join Date: Jan 2004
Location: Home of the Buckeyes!!
jjdustr340 is a Moderator
jjdustr340 is a Supporting Member
 has been a member for 10 years
jjdustr340 posts videos on PbNation
jjdustr340 supports our troops
jjdustr340 is one of the top 500 posters on PbNation
jjdustr340 is Legendary
Toby....

It's looking good. I think that there is still a little that can be added to it by members of the forum. Once all the info is out there, do you mind if I edit your post, just to clarify it and maybe re-word a few things?
jjdustr340 is offline   Reply With Quote
Old 04-15-2006, 10:15 AM #17
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
you may edit to your hearts content lol but yeah go ahead add or subtract if u wish. I will look around for some more quotes to....
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-17-2006, 11:37 AM #18
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
alright i threw some more stuff in there........idk what else can i put should i put something about co2 versus hpa so the newbs kno what to get or what they can use......
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-19-2006, 06:22 PM #19
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
jj sorry for havin three posts in a row but what else do u want added?
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Old 04-19-2006, 07:21 PM #20
jjdustr340
My son will bunker you.
 
jjdustr340's Avatar
 
Join Date: Jan 2004
Location: Home of the Buckeyes!!
jjdustr340 is a Moderator
jjdustr340 is a Supporting Member
 has been a member for 10 years
jjdustr340 posts videos on PbNation
jjdustr340 supports our troops
jjdustr340 is one of the top 500 posters on PbNation
jjdustr340 is Legendary
It's ok Toby.
I'll go through it sometime and clean it up a little. It's looking good!
Only reason I'm not on it right now is my internet is going extremly slow and driving me insane!
jjdustr340 is offline   Reply With Quote
Old 04-25-2006, 05:57 PM #21
Toby15custom
 
 
Toby15custom's Avatar
 
Join Date: Jan 2005
Location: Minnesota- it is to cold
hows your computer?
__________________
"Oh if paint was cheap like hookers"
Black Diablo Wrath-Evil Driver 14"-CP rail R15 board
Toby15custom is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump