[JoshGrrrr]

The old one was way out of date. Half of the websited didn't even work anymore. I threw this one together. If anyone wants anything added just post it and I will add it to the list.

MACHINING TOOLS AND EQUIPMENT
www.useenco.com
www.mcmaster.com
www.grainger.com
www.mscdirect.com
www.mini-lathe.com (Lots on good info on mini lathes and mills)

MATERIALS (Delrin, Aluminum, o-rings, Carbon Fiber etc.)
www.useenco.com
www.mcmaster.com
www.smallparts.com
www.grainger.com
www.mscdirect.com
www.metalexpress.net
www.onlinemetals.com

HOSES, FITTINGS, & GUAGES
www.hoseandfittings.com

ELECTRICAL COMPONANTS
www.radioshack.com
www.digi-key.com
www.jameco.com
www.solenoidcity.com
www.sciplus.com
www.allelectronics.com

HARD TO FIND MARKER PARTS
www.clippard.com (valves and rams)
www.airsoldier.com (misc rare marker parts)
www.compulsivepaintball.com
www.whitewolfairsmithing.com (phantom parts, pump kits, boomy freaks)
www.leespring.com (springs)
www.docsmachine.com

TECHNICAL INFO
www.warpig.com
www.ottersccustoms.com.
www.haveblue.org
http://www.bountyhunterspaintball.com/armory/ (Technical diagrams for many markers)

CUSTOM MACHINING
www.rainman229.com
www.docsmachine.com
www.punishers-customs.com
www.fbmfactory.com
www.jarrettcustommachining.com
www.eliapaintball.com


And remember, pretty much any set-screw, screw or o-ring you need can be found at Home Depot, Lowes, or any large hardware/home improvement store.

[crispy429]

found a place that carrys carbon fiber in sheets, blocks etc:

http://www.robotcombat.com/marketplace_metals.html

[moochems]

Originally Posted by parisinflames7

heres what i got, parts wise i was able to find 95 % of everything needed, the stuff i cant find can prolly be worked around (not using connectors for the eyes but just directly connectin them to the harness)
please note that part numbers listed are either the manufacturers part numbers or digi keys catolog numbers

For the 14 pt wiring harness the following is required

Molex 51110-1450-P

Digi-key part number WM18056-ND for the 14 space connector?s contacts


SW153-ND (Omron D2F-FL) is the part number for the 25 gram (W.A.S.) switch, stock 75 gram is Omron D2F-F, digikey # SW503-ND



http://www.allelectronics.com/cgi-bi...-61&type=store

http://www.allelectronics.com/cgi-bi...-63&type=store not entirely sure about that one, but im hard pressed to find anything else with my limited knowledge


For the 12 point harness you need

Molex 51110-1250-P

Digi-key part number WM18056-ND for the 12 space connector?s contacts




Eye Components
QED522-ND for emitter
QSD722-ND for detector


Miscellanious info
The intimidators wires are 26 AWG, but the contacts can take up to anywhere between a 22-30 AWG, you might want to try a thicker gauge that if you wire up eyes as people have problems with pinched eye wires often





I was unable to find the part numbers for the on/off switch if someone knows them please either email me kinksmanore@hotmail.com or post it

Timmy eyes, micro switches, etc.

[angel4life1]

www.mouser.com is another electronics website. its pretty nice.you should add this to your post joshgrrrr

[ratimpybigpimp]

Logicpaintball.com also does custom work.

[moochems]

Originally Posted by rammstein_5

here i will be a very nice guy, this isnt all of them u need to get off ur lazy *** and find them, btw the angel guys arent helpful i needed to find breech o rings and they wouldnt help me


ION
sollenoid head ~ 9/70
sollenoid barb~ 1x4-mm id
banjo fitting ~ 1.5x3-mm id
sft o ring~17/90
other sealing o rings for breech~ 20/70, 22/70, 17/70
feed tube o rings ~ 2x25.5- mm id
bolt tail ~ 10/70
near hte tail ~ 15/70
others ~ 20/70,14/70,15/90,2x16-mm id

MATRIx
STANDARD BOLT

Part--------------------------Oring size
Front wall (Outside)---------------#23
Front wall (inside)-----------------#17
Bolt nose (front)------------------#14
Bolt sail (middle)------------------#15
Bolt stem back--------------------#9
Bolt stem inside-------------------#10
Top hat (outside)-----------------#23
Top hat (large inside)-------------#17
Top hat (small inside)-------------#12
Rear wall-------------------------#23
Rear cap (outside)----------------#23
Manifold--------------------------#3

GEN-E BOLT

Part--------------------------Oring size
Front wall (Outside)---------------#23
Front wall (inside)-----------------#17 quad
Bolt nose (front)------------------#14 or 13
Bolt sail (middle)------------------#15
Bolt stem back--------------------#9
Bolt stem inside-------------------#9
Top hat (outside)-----------------#23
Top hat (large inside)-------------#17 quad
Top hat (small inside)-------------#13
Rear wall-------------------------#23
Rear cap (outside)----------------#23
Manifold--------------------------#3

PROTO
Material: buna-N type
durometer: Hard
durometer shore: Shore A 70
cross section shape is: round

List of sizes used on your matrix and where there located:

Size: / Location:

6 (piston small o-ring) located on LPR
9 (inside bolt stem,rear bolt stem)Bolt
10 (seal retainer o-ring) located on LPR
13 (top hat)bolt
14 (bolt tip)bolt / (piston large o-ring)LPR
15 (bolt sail, front bumper)bolt / (body o-rings)LPR
20 (outlet sleeve)bolt
111 (rear bumper)bolt

Mcmaster product price and product# (o-rings come in packs of 100):

O-ring size / Product number / Price

6 / 9452K14 / $2.17
9 / 9452K17 / $2.34
10 / 9452K18 / $2.34
13 / 9452K57 / $2.77
14 / 9452K58 / $2.89
15 / 9452K59 / $3.06
20 / 9452K74 / $4.00
111 / 9452K23 / $2.77


MACRO LINE
5173K16. Nylon 6 Tubing .150" ID, 1/4" OD, .05" Wall. Pressure too 922psi @ 70F.


DM4/5
014 - bolt tip
015 - sail and front bumper
009 - bolt stem
013 - Top Hat
020 - outer sleeve
111 - rear bumper

make sure they are round and made out of Buna-N material.

The clear o-ring for the beer can and the top hat is made out of urathane (polyurathane) and that size is 017.

tank o ring
Width
1/16"

Actual Width
.070"

Inside Diameter
5/8"

Actual Inside Diameter
.614"

Outside Diameter
3/4"

Actual Outside Diameter
.754"

use polyurathane


make sure to select standard



that was in my notepad, so it really is there for me to understand, idk if u will

Good for general info, if a mod chooses to delete it, PLEASE PM ME before doing so, so that I can copy it down elsewhere.

[imguessingurgay]

www.angelowners.com

[NYGuardians capt.]

first link not working

[PROTOgivesmeOWNAGE]

does anyone know what kind of dropfaward works on trilogy autocockers

[Intermision]

http://www.onlinemetalsupply.com/

[Topazbullet]

http://centuryspring.com/

[Lurker27]

Soldering guide

http://www.pbnation.com/showthread.php?p=22127659

[dyefreak315]

www.harborfreight.com
www.jlindustries.com

[gruntbull]

Destructive Customs for Machine work.

[ovenmitt]

yay finally cheap carbon fiber to try out, and some other nifty materials.

[PaintballerFourLife]

Originally Posted by gruntbull

Destructive Customs for Machine work.

QFT. www.destructivecustoms.com

[fishy#2]

Mcmaster no longer ships to Canada, making it difficult to get orings. I tried to locate some canadian places, without much success. After searching some US based places Enco, and small parts both appearently ship to canada. I'm ordering some orings today, and I'll let you guys know if it works out.

Edit: They do ship to Canada, and i just recieved my stuff. Beware of customs fees, and shipping fees though

[URgay4moleman]

http://www.predatorelectronics.com/i...emart&Itemid=1
for a decent board for most guns

[XxXEPIDEMICxXx]

http://dragonplate.com/

carbon fiber. tubes, rods, plates, blocks, skin. fairly affordable

[IonBeaver]

here is a good electronics place

http://www.goldmine-elec-products.com/default.asp

[demonik07]

ok guys so i have a lucky board and the damn molex pin the wire broke off of it now i can find any of them worth a **** so could somone help me ive lookd at radio shack dont got em ive looked on molexes website ill seee if my work can order me some but i doubt it ..but if you guys know a site shoot me a link to my pm would greatly be appreciated