[BurningPlaydoh]

Im looking to pick up a Vic soon, havent decided what gen, but I heard there was a problem with the magnetic bolt back cap popping up while the gun is aired up. Is this just the magnets coming loose which is easily fixed, or was the cause a more serious issue?

[bulzeye]

just magnets coming loose and is a very easy fix

[BurningPlaydoh]

Originally Posted by bulzeye

just magnets coming loose and is a very easy fix

Good to hear, looks like I'll be picking up a Victory soon!

[wafflecakee]

With the eyes on and nothing in the breech if I pull the trigger my victory fires a delayed shot. Why does it shoot at all if the eyes are reading properly that no paint is in there?

[wafflecakee]

My gun is usually leaking slightly down the breech after every day of play, it seems to just be grease on the doughnut. Is this my gun telling me there's too much grease on the bolt guide?

[juggernaught_lives]

Originally Posted by wafflecakee

With the eyes on and nothing in the breech if I pull the trigger my victory fires a delayed shot. Why does it shoot at all if the eyes are reading properly that no paint is in there?

There are 2 versions of the Eyes on

Forced Shot - If you running your fingers on the trigger with NO ball in the Breech, the Marker it will not shoot at all. If you hold down the trigger with NO ball in the breech, the Marker will fire a shot after 1 second.

Delayed Shot - If you the trigger once (1) with NO ball in the Breech, the Marker will fire a shot after about 1 second. If you hold down the trigger with NO ball in the breech, the Marker will fire a shot after 1 second.

Originally Posted by wafflecakee

My gun is usually leaking slightly down the breech after every day of play, it seems to just be grease on the doughnut. Is this my gun telling me there's too much grease on the bolt guide?

Yes too much Grease will cause leaks and performance issues not to mention you run the risk of shooting lube into your barrel causing all kinds of paint issues.

[wafflecakee]

What is the allen key size to take the back cap off of the victory engine? I've got two sets and neither of them have this size.

[wafflecakee]

nevermind, got it.

[Carlos_Is_King]

I got a used 2k5 Alias and Rapper. Can I send them into Blast to be inspected and tuned. The Rapper also has a leak from the gear drive

[herk8240]

Yes

[griffan2]

you say at the bottom that the LPR for a HP engine should be at 50 pounds. is that correct? I thought it should be at 80-85

[meatwad969]

Originally Posted by griffan2

you say at the bottom that the LPR for a HP engine should be at 50 pounds. is that correct? I thought it should be at 80-85

the 50psi is for tadao board users only with the proficiency engine. i do not recall what the specs are if you are supercharged.

im going to go through and read it the sticky again, but i did not see what is required to run G6R grips on a gen1 marq(marq 6, 7, rapper, closer, darq, RL, edge). I seem to remember something about having to have the gripframe altered? can anyone expand on this?

[gamer565]

Originally Posted by meatwad969

the 50psi is for tadao board users only with the proficiency engine. i do not recall what the specs are if you are supercharged.

im going to go through and read it the sticky again, but i did not see what is required to run G6R grips on a gen1 marq(marq 6, 7, rapper, closer, darq, RL, edge). I seem to remember something about having to have the gripframe altered? can anyone expand on this?

50 psi is awfully low for the lpr, in any engine.

You can use g6r grips on gen 1 marq, you just won't have the bottom screw holding it unless you still and tap the frame. Or make a hole in the grip.

[meatwad969]

Originally Posted by gamer565

50 psi is awfully low for the lpr, in any engine.

You can use g6r grips on gen 1 marq, you just won't have the bottom screw holding it unless you still and tap the frame. Or make a hole in the grip.

sweet, thanks.

and i was quoting the front page for the 50psi blurb. Im about to purchase a closer today with the SC engine and i dont remember the sweet spots just like riding a bike right? itll come with time

[quattroginger]

i have the Gen 2 Marq Victory manual however i cannot find a break down of the o-rings throughout marker. i purchased a sc ripper and a additional vcom engine for it.

the manual has break down of the 2 engines (sc and vcom) however nothing on the marker. there is also a o-ring chart however i don't necessarily understand each location based of the "part name".

1. Is there a break down, or walk through to replacing o-rings/locations?

2. what is Buna? ex: it may say 1x12mm then the next part is 1x12mm Buna.

thanks guys

[gamer565]

Originally Posted by quattroginger

i have the Gen 2 Marq Victory manual however i cannot find a break down of the o-rings throughout marker. i purchased a sc ripper and a additional vcom engine for it.

the manual has break down of the 2 engines (sc and vcom) however nothing on the marker. there is also a o-ring chart however i don't necessarily understand each location based of the "part name".

1. Is there a break down, or walk through to replacing o-rings/locations?

2. what is Buna? ex: it may say 1x12mm then the next part is 1x12mm Buna.

thanks guys

https://www.pbnation.com/showthread.php?t=3956138

Buna is the type of oring, like viton and urethane oring.

[quattroginger]

thanks gamer.

[Spyder124]

Is there a thread/sticky for identifying Marq engines? I picked up a V1 Victory and I'm not 100% sure what engine it has.

[gamer565]

Originally Posted by Spyder124

Is there a thread/sticky for identifying Marq engines? I picked up a V1 Victory and I'm not 100% sure what engine it has.

SC is in the first page, here are the others:

https://www.pbnation.com/showthread.php?t=3956138

https://www.pbnation.com/showthread.php?t=4496385

[sgtsprinkless]

They don't service the marq 6 anymore