[The Field Tech]

Q: how do I take off the bottomline stuff to replace it w/ a drop forward?

A:

Step 1). take off macroline/SS hose off the Evil On/Off.

Step 2). Loosen set screw on top of the micro rail on the bottom of the grip frame.

Step 3). Slide off On/Off in either direction very slowly as not to damage it and set it aside.

Step 4). Unscrew the screws in the bottom of the grip frame to take off the micro rail (may require some force if they are lock-tit'd in).

Step 5). Set Drop Forward and replace the screws you just removed in the previous step.

Step 6). Replace Evil On/Off (if you are using the stock on/off) and replace set screw.

Step 7). Replace/Recut SS/Macroline to On/Off and rechrono.

[mauikalohe]

Originally posted by Dubie998
this is a dumb question, but exactly what needs to be cleaned and lubed, and should i use lube or grease?

Cleaned:
Normal stuff like barrel internals.
Wipign down the bolt etc..
If your tech enough it's good to clean just about everypart from time to time

Lubed:
Hammer, inside and out:Both oil or Grease (puss dow33) will work - just dont add too much grease or oil.
Regulator: - drops of oil in the off/on or rebuild with grease

DO NOT OIL OR GREASE BOLT

[weetbix]

How to properly clean and maintain the Evil Omen

Ok well i have somen time on my hands so i desided that i would make this thread, I realise that most of you may know this already but this will help anyone new to the omen.

First you need to wipe down the out side of the gun from any dirt/paint etc

Then take out the feild strip pin and remove the bolt, hammer etc, wipe off the Bolt and lube the Hammer o-ring

Now remove the cam cover/feedneck, you do this by taking out two allen bolts, one on the right side of the gun and the other on the middle of the body

Once this is off wipe off any paint on the inside of the gun

Now put back the marker in the opposite order that you took it apart in

I recomend that you take apart and lube your regulator every 4 cases or so, omenworker made a good link on this so here is a link to it (it is in the middle of the page)

Omenworkers Detonator Stripdown

And that is what i do personally to look after my omen, hope this helps someone out there

Alastair

[mauikalohe]

not even sure they make 48 Fiber wrap tanks. But I think the wieght difference is a 1-4 pounds - it really varies from tank size, type and brand

Here is a thread going on now about alm/steel tanks
https://www.pbnation.com/showthread.p...hreadid=824559

Also ask around in the air systems forum:
https://www.pbnation.com/forumdisplay.php?s=&forumid=151

My take is it is a good tank that will hold some resell value for a little while - and could be a good backup tank if you ever gor fiber wrapped.

IMO fiber tanks are much better on the field but buying used can be a headache - new can be costly.

Ross may be able to get you a deal or bundle on any tank - email him to see what you can do

[Max=Omen453]

Whats, the best hpa tank for the omen?? and not the scion, something in a decent price range

[Bob Bobbity]

probably a crossfire or a pure energy tank, cheapest size to get is a 48/3000 but you wont get much shots off of that and it isnt fiber wrapped, cheapest fiber wrapped tank is a 68/3000 but I prefer either 45/4500 or 68/4500 those will both get you quite a few shots.

[Scion]

Crossfire, Pure Energy, and the Macdev Legion Air will all do you nicely.

[PB Commando]

is there any other thing i can use to get the snap ring off (like pliers) ?

[skateandpaint (Banned)]

i know this sounds like a noob question but i am a noob to omens.

what is the locking screw on the reg

[mg101153]

Originally posted by skateandpaint
i know this sounds like a noob question but i am a noob to omens.

what is the locking screw on the reg

read the manuel

[skateandpaint (Banned)]

if i owned one i would

[Vulture1]

Do I have to adjust the re-cock and velocity before I play every time, even if I’m using the same paintballs PMI big ball or PMI premium?

[Tesko]

Vulture1 - Yes, yes you do. Velocity won't be a big change if you haven't fiddled with the reg. Just put the recock screw all the way in, shoot a couple balls over the chrono, adjust velocity to 10 FPS above your field limit, then without paint, dryfire and turn the recock screw out in quarter turns, taking time to shoot between that, until it consistantly recocks. Take it back over the chrono with paint to make sure you're shooting within legal limits.

[Vulture1]

Thanx Tesko, did Evil fix all the problems they used to have with the omen? i know they had some problems with the first ones they released.

[Tesko]

Yes Vulture1, and the latest Omen's are shipping with the 1.5 Upgrades in them stock.

[Max=Omen453]

How do i know if i have a 1.5 omen, cause i have a red back block and all, but i dont know if i have the board, and when i opened it up to look at cam arms they were opposite to what i could see, and im a pansy with opening it up. also how do i open it up to replace the board if i buy a 1.5 board, and cam arms.

Thanks

[Omen x13]

when did you buy it and where did you buy it from

[Max=Omen453]

i bought it slighltly used off of ebay in 04, i dont think it was even used though, the guy just opened the box

[Vulture1]

What is the best paint to use with the evil omen?

Something not expensive.

[vmnx9]

i was looking on the evil parts site, and i saw a hammer bumper. my omen is working alright except one small problem. i start out shooting i shott like 20 balls then i have to pull back the coking rod. then i shott 10 and i have to pull back the cocking rod. it gets down after a while to pulling back the cocking rod after every shot. do i need to replace the hammer bumper. cause i little foam like thing in my gun is shredded

[Kaotix]

It probably wouldn't hurt to get that replaced... but did you know you have to readjust the recock pressure before every use?