marq not programming right

Duell · 01-13-2009, 10:08 PM

My marq is not programming right. It is the Frenzy 3.0 board. I put a dipswitch to the "ON" position and hold the trigger and turn it on and it goes white. I let go of the trigger and it starts flashing white. It continues to flash. It never stops flashing. I let it go over 50 once, never stopped. It wont let me reprogram it either. it wont take the new settings that I put in. Any help?

$acceleration$ · 01-13-2009, 10:14 PM

do you have the frenzy 3.0 bored? are you flipping the right switch?

Duell · 01-13-2009, 10:17 PM

yes it is. sorry and yes it is the right switch

IgnoranceInABag · 01-13-2009, 10:42 PM

sounds like it isnt flashed. which dipswitch?

kizzlesNbits · 01-13-2009, 11:04 PM

i have the same problem...tried messing around with it for a long while...nothing worked

IgnoranceInABag · 01-13-2009, 11:06 PM

is it going straight white? or does it go through all the colors real fast first?

Duell · 01-14-2009, 12:20 PM

all the colors real fast and then white then white flashing. and all dipswitches do the same thing except 4 and 5 I just keep those off cause those are just shooting modes.

SpyderOWNAGE · 01-14-2009, 05:23 PM

You don't have 3.0. You have 2.0

Flashing white = Eyes off

IgnoranceInABag · 01-14-2009, 05:51 PM

yup, you need to send your board in. but i would suggest waiting till the next programing mode comes out

Duell · 01-14-2009, 06:43 PM

oh... dang ok i was told by seller it was 3.0 ok thank you. where can I get a manual for the 2.0 board?

IgnoranceInABag · 01-14-2009, 06:59 PM

what do you want to do?
the programming is the exact same except the old board isnt as programable.
dipswitch
1 is fine tune cycle delay, its either on or off
2 is debounce, it is either max or off
3 is rof, it is either capped at 15 (on) or uncapped (off)
4 and 5 are firing modes and are the same as 3.0
6 is dwell, it is eithre 8(off) or 10(on)

JesseSands2 · 01-15-2009, 12:05 AM

I think I have the 2.0 board as well and have a question. I wanted to turn dipswitch 2 (debounce) to the ON position, but when I flip it to 'ON' my gun wont turn on normally so I always have to turn it back to off. Is there something else I need to do? I actaully have all my switches set to off right now, but I know when I had it on ramping i had moved switch 4 or 5 to 'ON' and it worked fine.

SpyderOWNAGE · 01-15-2009, 12:15 AM

Are you sure you don't have 3.0?

What happens to the LED when you turn the gun on with #2 on? Does it start to blink (I think the LED color is green, can't remember)?

Duell · 01-15-2009, 12:14 PM

Quote:

Originally Posted by IgnoranceInABag

what do you want to do?
the programming is the exact same except the old board isnt as programable.
dipswitch
1 is fine tune cycle delay, its either on or off
2 is debounce, it is either max or off
3 is rof, it is either capped at 15 (on) or uncapped (off)
4 and 5 are firing modes and are the same as 3.0
6 is dwell, it is eithre 8(off) or 10(on)

ok thank you very much

kizzlesNbits · 01-15-2009, 05:01 PM

with the 2.0 how do you turn the eyes off ???

IgnoranceInABag · 01-15-2009, 05:01 PM

same way as 3.0. hold the trigger while powering the board up

lamar · 01-17-2009, 12:51 AM

I am having the same problem ,but mine is flashing orange. There are no eye malfunction at all as well.The eyes are working, because i took them out of my closer just to check.

IgnoranceInABag · 01-17-2009, 01:43 AM

^^change your battery