[oggfueler]

Originally Posted by ApoC_101

things to add:

-when removing the backblock, it is not necessary to totally unscrew it... simply rotating it 180 degrees will allow you to slide the pump handle off, with the pump rod and the backblock still attached.

-when removing the hammer, it is best to unscrew the lug say, 3 complete turns, so when you re-install it you don't have to re-tune it, just screw it back in the same amount of complete turns.

-you can also apply that technique with the IVG, to re-install it without losing your velocity setting. I usually check its position with a micrometer, but counting the turns works well enough.

Whoa bro,,, I thought I was anal about my gear

[ApoC_101]

Originally Posted by oggfueler

Whoa bro,,, I thought I was anal about my gear

I'm a machinist FFS, I do **** right every time, a hell of a lot faster than anyone else

[iampogi]

Originally Posted by Talfuchre

Sticky it.

Pogi - if you need a video - you are a little lost and need to sell your marker.

TF

haha TF that was uncalled for...you...you... meany.
lol i did actually.. like a month ago. i was thinking of picking up your s5 basic but after this attack against my internet manhood i think im going to take my business elsewhere
(btw tf, check out tech-pb.. hehe filter.. under the ccm sub-forum. someone is looking for a s5 basic if you have not sold it yet)

[WarHamster]

Added & cited contributions from ApoC & Castro.

[ApoC_101]

got a video tutorial to accompany the photos for ya, uploading in a sec here.

[NoelyDeezNutz]

aww damn... i was about to post that I would do a video... lol

[iampogi]

Originally Posted by NoelyDeezNutz

aww damn... i was about to post that I would do a video... lol

the more the merrier! i just find it alot easier to learn when i see what is going on. and it would also complete this thread making it a one-stop-shop for pump maintenance and tunning galore
edit:
noley where you part of the paintballgroup in myspace?? idk your name seems familiar

[NoelyDeezNutz]

Im all over.... I'm the only NoelyDeezNutz out there (that im aware of)

[ApoC_101]

All done (youtube went down for maintenance hence the delay):

http://www.youtube.com/watch?v=eaBNYj3f8Ps
http://www.youtube.com/watch?v=k4IBUgHi8Oo

part 1:

part 2:

[impact4]

sticky this already.

[wallify]

Eagerly awaiting the springing section.

[ApoC_101]

we currently have 11 stickies in this forum... that is already a **** ton. maybe we could toss one out?

[jk_6109]

If this were stickied it would get rid of so many threads. Wait, no, i forgot nobody reads the stickies...
I still think it should be stickied.

[BurntGrits]

Originally Posted by wallify

Eagerly awaiting the springing section.

I'm waiting for this section as well....

[timmah333]

Originally Posted by BurntGrits

I'm waiting for this section as well....

me three!

[spud01]

WarHamster-You are my Hero A BIG from me. And of course STICKY!!!

ApoC_101-Thanks for helping out us "special" pumpers

[oggfueler]

WarHamster or ApoC_101... if either of you have nestled in your infinite knowledge a little "Spring tuning 101 for mini'd Snipers" it'd be sweet if you could add it to this or start one... my Superbolt is about to give me an aneurysm.

[WarHamster]

I fully intend to get around to the springing guide eventually. The little bit I have started has been harrassing me to finish it.

Unfortunately I'm doing my student teaching this semester so that's been eating up a ton of my time. Finishing that tutorial has slipped way down my to-do list below: lesson planning, eating, sleeping, and staying sane.

[oggfueler]

Best of luck to your bro

Git R Dun when you can

[05 ProStock]

Sticky this already.

[P8NTBAWL'ER]

stickyy