Avec le peu d'images que j'ai trouvé sur le web du moteur du démon (version 2013).
j'ai tenter d'imaginer son fonctionnement mais à la lecture de la description de
l'upgrade j'ai dû forcément me tromper: il y est écrit qu'il n'y a qu'un seul
nouveau perçage du corps (pour l'extraction) moi j'ai dû en faire deux: un pour
l'alimentation permanente de la valve à la pression de service
(le fait de mettre la valve sous pression permet entre autres de la forçai par
déséquilibre des surfaces de poussée à se déplacer vers l'arrière (quand elle n'est
plus contrainte par des forces extérieures))
et l'autre pour la
distribution de la commande du solénoïde , il y a aussi un ressort que je ne vois
nul part,
donc je suppose qu'il est à peu près à la même place que sur le luxe (pour éviter
de blesser les joints) (et peut être aussi pour une question d'esthétique)).
Le ressort doit probablement être conique pour rester en place (coincé dans une
gorge).
Je pense que détendu il ne doit pas permettre l'ouverture du power tube/la chambre
de tir pour éviter qu'à la mise sous pression en air du système il puisse y avoir
un coup intempestif.
Je suppose que c'est ce ressort (en amorçant le décollage), plus(+) les joints dur (qui
réduisent la surface de friction), plus(+) l'augmentation du volume de la chambre de tir
(qui assure un transfert d'énergie plus doux mais pendant plus(+) "longtemps")
qui ont permit de descendre la pression de 125 à 90 psi.
With little of images which I found on Web of the engine of the devil (version 2013).
I have to try to imagine his(her,its) functioning but in the reading of the
description of the upgrade I had to necessarily make a mistake: it is written there
that there is only an only new drilling of the body (for the extraction) I I had to
make two: one for the permanent food(supply) of the valve in the service pressure
(the fact of putting the valve under pressure allows among others of forced her(it)
by imbalance of the surfaces of push to move towards the back (when she(it) is not
any more forced by outside strengths)) and the other one for the distribution(casting)
of the command(order) of the solenoid, there is also a spring(competence) which I see
no leaves, thus I suppose that he(it) is about on the same place(square) as on the
luxe ((To avoid hurting joints) (and can be also for a question of aesthetics)).
The spring(competence) must probably be conical to stay ready(in position)
(clamped in a throat(breast)).
I think that relaxed he does not have to allow the opening of the power tube/la bring
to room temperature of shooting(firing) to avoid that in the putting under pressure in
air(sight) of the system he can have an inconvenient blow there.
I suppose that this spring(competence) (while beginning(priming) the take-off), more
(+) joints hard (which reduce the surface of friction), more (+) the increase of the
volume of the room(chamber) of shooting(firing) (which assures(insures) a softer
transfer of energy but during more (+) "for a long time") which have allowed to
lower(to go down) the pressure from 125 to 90 psi.
sur la seule photo où on voit la "can" (sans la valve) c'est difficile de se rendre
compte s'il y a une différence d'épaisseur de section de la "can"
mais dans mon hypothèse elle est indispensable alors je l'ai dessiné
la section est plus fine vers l'arrière de ce fait les surface avant et arrière de
la valve ne sont pas égales, la surface arrière de la valve étant légèrement plus
grande le déséquilibre de pousser produira un mouvement vers l'arrière (a condition
qu'il n'y est pas de contraintes extérieures)
On the only photo where we see the "can" (without the valve) it is difficult to
realize if there is a difference of thickness of section of the "can" but in my
hypothesis she(it) is indispensable then I drew him(it) the section is finer towards
the back of this fact surfaces them before and back of the valve are not equal, the
back surface of the valve being slightly bigger the imbalance to grow will produce a
movement towards the back (provided that there is no external constraints)
-----------
Y a-t-il un décaisser ?
Y he disburse one?
-------------------
je suppose qu'il y a un petit décaisser qui permet d'avoir la face arrière de la
valve un peu plus volumineuse
I guess there's a little disburse that allows for the rear of the
valve slightly bulkier
-----------------
première hypothèse peu probable à mon avis
parce que je ne vois pas de force qui peut ramener la valve en avant
first hypothesis unlikely in my opinion
because I see no force that can bring the valve forward
ici la valve jouerait à peu près le rôle de l'ancienne QEV.
here the valve play about the role of the old QEV.
ici je respecte le cota de nouveau percement mais je n'arrive pas à comprendre d'où
provient
la force qui ramène la valve vers l'avant ( sachant que je n'ose pas imaginer que le
retour vers l'avant de la valve soit produit/assuré par l'effet seringue/piston)
here I respect cota new piercing but I can not understand where
comes
force which brings the valve forward (knowing that I can not imagine that the
back to the front of the valve is produced/provided by the effect syringe/piston)
--------------------------
hypothèse la plus probable pour la position du ressort mais qui colle pas avec la photo.
(moteur en phase de tir)
deuxième hypothèse plus probable du point de vue du fonctionnement mais qui colle pas
du tout avec le descriptif
The most probable hypothesis to the position of the spring, but that does not fit with the picture.
(motor in shooting phase )
second assumption most likely in terms of the operation, but that does not fit
all with the descriptive