[Rob @ Ninja PB]

Originally Posted by trisgale

brand new 77/45 1 day old, first time using it I removed from my marker and leaking at pin valve.

not very happy right now.


update: took it to local shop where i bought it from. Fixed, i guess an easy fix but i'm a newb.

I guess its good to support your local shops.

trisgale. Just as a heads up, any regulator can have an issue after the first fill, not due to any fault of the regulator. If a compressor is not maintained properly, it can blow dirty air down the fill line, through your reg, into your bottle, and back up into your reg. The smallest piece of debris can cause an oring to fail.

Please do not assume the reg is the cause of the issue because it might not be. Always consult the manufacture or a local shop (as you did) for assistance if a problem arises.

[Rob @ Ninja PB]

Originally Posted by konnorH

I have had my dura 77 tank for about 2 months now and over the past month I've noticed it losing the matte/dust feel. It is now almost completely smooth and am I not to happy about that because one of the sole reasons for buying the tank was the feel. Just wondering if there is a way to get this problem resolved.

There sure is. If there is an issue with the dura coating or gel coat on our other bottles, you can click this link and see if you can send it in to have the dura coating replaced. Some of the first batch had a lighter than normal coating due to our manufacturer rushing the production process to get tanks to us when we first released them and the Dura coating could rub off on those. If you send it in, the bottle manufacturer will take care of you on it if this is occurring.

http://97.74.153.121/NinjaWarrantyTa...s/warranty.php

^Click link and follow instructions^

[Rob @ Ninja PB]

Thanks, Stewylouie and HeadHunter59. I appreciate you guys helping these fellas out while we were closed.

Stewy, we going to see you and John in Chicago or at Cup this year?

[forstgump]

I take it Ohio is backed up on coating tanks? Mine was sent out and received in February and I'm still waiting on it's return.

[deadbodyboy]

Originally Posted by Rob @ Ninja PB

you must click this link and follow the instructions to have the issue taken care of on the cracks in the outer gel coat. We will not be swapping out bottles at any events. Bottles must go through the warranty process with our bottle manufacturer:

http://97.74.153.121/NinjaWarrantyTa...s/warranty.php

However, we will be at Living Legends and i'm looking forward to getting out there and shooting it up with everyone

Ok thanks Rob!

[Rob @ Ninja PB]

Originally Posted by forstgump

I take it Ohio is backed up on coating tanks? Mine was sent out and received in February and I'm still waiting on it's return.

Yes, they just moved to a new location and it took some time for them to set up all of the machines and get rolling with production and warranty. If you like, you can email me at rob@ninjapaintball.com with all of the information you populated on the warranty page and I can forward it up for you and see if we can get you an update.

[forstgump]

Originally Posted by Rob @ Ninja PB

Yes, they just moved to a new location and it took some time for them to set up all of the machines and get rolling with production and warranty. If you like, you can email me at rob@ninjapaintball.com with all of the information you populated on the warranty page and I can forward it up for you and see if we can get you an update.

Thanks. That's all I needed to know. I can wait.

[lunatic209]

I found a guy selling a Ninja 70/45 but I want to know exactly how much longer the 70/45 is compared to the 68/45. I'm 5'2 so I have relatively short arm length. Can I get measurements for a 70/45 compared to the 68/45?Highly appreciated.

[bub030203]

quick question. I bought a tank off a pbn member. It is a 68/45 Ninja tank with pro reg, and the lettering on the regulator is 10-11-SBM. the birth of the tank is 02-11. I needed to remove some shims and not knowing previously how many were POSSIBLY removed before I took off the bonnet to the tank and there were only 2 silver shims under the spring. QUESTION IS: By removing both these and leaving NO Shims AT ALL other then the spring will my tank pressure be at 450psi now? I'm using it on a G6R and before I gas the gun up I wanna make sure my tank is set correctly. Thanks.

[Rob @ Ninja PB]

Originally Posted by lunatic209

I found a guy selling a Ninja 70/45 but I want to know exactly how much longer the 70/45 is compared to the 68/45. I'm 5'2 so I have relatively short arm length. Can I get measurements for a 70/45 compared to the 68/45?Highly appreciated.

about an inch. the 70 is very similar in length to our new Dura 77's.

[Rob @ Ninja PB]

Originally Posted by bub030203

quick question. I bought a tank off a pbn member. It is a 68/45 Ninja tank with pro reg, and the lettering on the regulator is 10-11-SBM. the birth of the tank is 02-11. I needed to remove some shims and not knowing previously how many were POSSIBLY removed before I took off the bonnet to the tank and there were only 2 silver shims under the spring. QUESTION IS: By removing both these and leaving NO Shims AT ALL other then the spring will my tank pressure be at 450psi now? I'm using it on a G6R and before I gas the gun up I wanna make sure my tank is set correctly. Thanks.

Already responded to your pm. Please only post questions in a pm or on the Ask a Ninja Tech thread. Posting in multiple locations can cause confusion.

[lunatic209]

Originally Posted by Rob @ Ninja PB

about an inch. the 70 is very similar in length to our new Dura 77's.

Thanks for the quick reply. Just what I wanted to know.

[Bellamy803]

Hey ninja, what's the deal with the light blue gloss finished tanks? Stumbled across one today and thinking about getting it. How many we're made and why did you guys choose not to continue? Thanks

[Bellamy803]

Originally Posted by Bellamy803

Hey ninja, what's the deal with the light blue gloss finished tanks? Stumbled across one today and thinking about getting it. How many we're made and why did you guys choose not to continue? Thanks

Here's my thread with the pic of it. Looks pretty good I have just been wanting the the dura finish for so long now I don't know which to choose

https://www.pbnation.com/showthread.p...ght=bellamy803

[Rob @ Ninja PB]

Originally Posted by Bellamy803

Here's my thread with the pic of it. Looks pretty good I have just been wanting the the dura finish for so long now I don't know which to choose

https://www.pbnation.com/showthread.p...ght=bellamy803

Thanks for the link. I'll post in the thread now.

EDIT - that is a 1 of a kind Ninja cylinder

[-Lightning-]

Quick question, can I run a dm4 with no shims in a UL ref

[HeadHunter59]

You shouldn't have any problems running it on LP.

If you do throw 1 or 2 silvers in and should be a ok.

[-Lightning-]

It only has 2 red which are both rem0ved

[bokyo102]

planning to buy a Ninja Remote Straight w/ Push to Connect(PTC) to use for Tippman Tipx Pistol Remote Adapter, will this work? i noticed that the PTC Male fitting is different from the Tipx male fitting. Thanks

[Rob @ Ninja PB]

Originally Posted by -Lightning-

It only has 2 red which are both rem0ved

that should get you to about 500psi if only 2 red shims originally came with the reg from the factory. If you get shootdown or cant chrono over a certain velocity, add 1 red shim back in.

[Rob @ Ninja PB]

Originally Posted by bokyo102

planning to buy a Ninja Remote Straight w/ Push to Connect(PTC) to use for Tippman Tipx Pistol Remote Adapter, will this work? i noticed that the PTC Male fitting is different from the Tipx male fitting. Thanks

no. you will need a push to connect ASA adapter.