[hvacman]

Originally Posted by Bill

Make sure the Zick 2 has the large bumper in the back of the ram and the clear bumper in the rammer cap.

All there and all good. When I removed the rammer cap to check the bumpers it was still holding air after two weeks! Guess I got a good seal.
Thats what made it feel different, now without the air it feels normal.
Thanks again!

[frost1235]

I have an ego11, and I'm having issues with the act/pk bps meter.
When I use it on training, or even really firing my marker, instead of updating the act/pk bps, it stays at 00.0 bps until I change the screen to the timer, shot counter, then back to the act/pk bps. At this point, it will show the old bps.

If its unclear, I can show a vid on youtube later.
Is something up with the board?

[Bill]

Originally Posted by azndave

I fear it probably is the solenoid, which I cannot realistically service...

Leak is right here:

If it isnt the LPR housing 14x2 orings, the LPR piston or the rammer orings, then it is most likely the solenoid.

[Bill]

Originally Posted by Lv_archeaon

Hi,

I own an ego 09 with a cure 3 bolt. the breach and bolt are not worn at all but im having trouble with breakage after 80 or so shots. I have a rotor so i know feeding the gun isnt the issue. I think it might be my gun settings, but I dont know what the best settings are for it. Suggestions..?

Do you have the plank kit installed in the solenoid?

If so, you can raise the dwell slightly.

Change the detents.

Do you have the factory board in the rotor? if not, the setting could be set to high for the little rubber detents.

[Bill]

Originally Posted by Hyaboosta

thanks for the info. so i'll set dwell to 14. lpr 1 turn from flush and then do i adjust the hpr until i chrono about 280?

yes, using the HPR. Start with the screw all the way out. Then turn it in about 3.5 turns. Chrono from there.

[Bill]

Originally Posted by 0celot

Thanks I apparently bought a pack of bad batteries (energizer alkaline) It was showing full battery but I went and bought some Duracell and wha la works like a charm! Whats the point of having a battery level indicator if it dont work properly?

The battery meter is for Volts, not Amps. A bad batch of batteries may read 9volts but the Amperage output could be compromised. Basically there is enough voltage but the "upkeep" isnt enough to maintain the proper level of power the gun needs.

[Bill]

Originally Posted by hvacman

All there and all good. When I removed the rammer cap to check the bumpers it was still holding air after two weeks! Guess I got a good seal.
Thats what made it feel different, now without the air it feels normal.
Thanks again!

The rear bumper inside the rammer cap. It gives a more spongy feeling.

[Bill]

Originally Posted by frost1235

I have an ego11, and I'm having issues with the act/pk bps meter.
When I use it on training, or even really firing my marker, instead of updating the act/pk bps, it stays at 00.0 bps until I change the screen to the timer, shot counter, then back to the act/pk bps. At this point, it will show the old bps.

If its unclear, I can show a vid on youtube later.
Is something up with the board?

I recommend sending programming issues to: info@planeteclipse.com

[Lv_archeaon]

Originally Posted by Bill

Do you have the plank kit installed in the solenoid?

If so, you can raise the dwell slightly.

Change the detents.

Do you have the factory board in the rotor? if not, the setting could be set to high for the little rubber detents.

I'm not sure what a plank kit is, all I know is the gun and rotor are both bone stock with the exception of the cure 3. I'll try changing the detents and and upping the dwel and see if that helps.

[Bill]

Check the rammer. Make sure the middle oring isnt getting beat up. If so, you need to purchase a plank kit.

[DuttDutt48]

Will an '09 stock Ego board fit in an '08 frame?

[jasoncompton78]

Hey bill,


I am getting ready to replace the lcd mdule display on an ego10 as it has a crack in it and is unreadable, and i was wondering how and, if possible, can some tell/show me how exactly to get the old one off, im not sure if its soldered on or not, i couldnt imagine it would be, thanks, if you need more, it is my friends and I don't currently have it in my hands to know

[Boe 23]

hey bill i have a question i just picked up a dynasty ego 10 and i was wondering if there is anyway i could get a custom splash screen or board flash so i could use eportal, Any info on this subject would be great

thank you

[PBAdvantage]

Bill,
I recently put mid pressure SL3 regulator on my 08 Ego and when I turn my velocity to anything over 265-275 air starts venting out of the side port and doesn't stop until I turn it back down what is the issue here? If it's o-rings can I use any of the ones provided in my rebuild kit and what kind of grease do I use or can I just use oil?

Thanks

[fenixreaper]

Hi, Bill.
Yesterday I recieved an Ego 10. It's used. Counter says that Ego made 83948 shots. The problem is when I turn eyes off, I can't hear solenoid because off trigger clicking like I did with my ETek 3. Is it solenoid so quiet or it's broken? I can't try air it up, because my tank is a little bit far from my current location.

Thank you.

[terry1966]

Hey, Bill, i have a 06 ego and i just all of sudden put air too it and it would fire but ball would just roll out. Then i had air to it took of the grip and all the sudden all kinds of air would come out. I took it apart to the solenoid and there is a box connected to the solenoid, there is one clip holding it and looks like there should be another one, Would this be my problem?

[Bill]

Originally Posted by DuttDutt48

Will an '09 stock Ego board fit in an '08 frame?

Sorry but haven't tried it. If you have both, cant hurt to find out.

[Bill]

Originally Posted by Boe 23

hey bill i have a question i just picked up a dynasty ego 10 and i was wondering if there is anyway i could get a custom splash screen or board flash so i could use eportal, Any info on this subject would be great

thank you

Sorry but there isn't.

[JDempsey12]

Hey Bill,
I've got an Ego8 that I used in a tournament this past weekend. It was extremely cold and snowing but the only problems I had during the day were that it had a tiny leak and it did not chrono consistently. I used it and it worked great (aside from the leak and FPS problems). I took it home, lubed and cleaned everything and then set it down. A few days later, I wanted to see where the leak was coming from so I unscrewed the body and looked at the solenoid. The leak was gone and I put it back together. I tried to shoot it a few days ago and everytime it fires, it makes this weird popping noise itstead of how it normally sounds. It won't even shoot any paintballs either. Also, my teammate owns a Geo and he's having the exact same problem. Could the weather have done something to our guns?

[eduds]

bill,
I purchased a used ego with the z2 rammer in it only ploblem is the large black bumper on the back of rammer is missing. I searched and cannot find that bumper anywhere, only the one that goes in the cap. I dont see the need to buy a whole new rammer kit cause of just that part, any help greatly appreciated.

[pb slenger]

Do the CSL's come from the factory with the LP or HP valve installed in them?
Thanks,
Dj