Nerve velocity/recharge rate problems

WillyW0nka · 08-30-2007, 10:40 AM

I didn't use Dow55 on the gun, since shocker lube is reccomended to be 33 I figured nerve might be too.

And I know how to change dwell, and check for noid, the problem is, which noid is which? You said they're both parker, then you told me to put it at 40 ms if its a humphrey

RHChan84 · 08-30-2007, 10:44 AM

lol oh. My mistake, sorry.

I meant Black is Parker and White/Silver is Humphrey.

WillyW0nka · 08-30-2007, 10:47 AM

thanks

I'll go check, but will that will have anything to do with the slow recharge rate?

RHChan84 · 08-30-2007, 10:54 AM

It could. If you already replace battery, clean an lubed both regs then the only thing left would be the dwell setting.

WillyW0nka · 08-30-2007, 11:34 AM

alright I checked it, and its black/silver, so my dwell setting is fine. I'll lube up the regs when I get my hands on some dow33

Until then, it doesn't seem to shoot too bad. I don't have a chrono though. I was shooting at a spot about 30+ feet away and it shot pretty well, but the gauge reading was saying it probably had mad drop off lol. It wasn't going below 140 psi though.

team_xile · 08-30-2007, 04:19 PM

well we are getting somewhere then.

WillyW0nka · 08-30-2007, 04:56 PM

I hate the stock trigger, are they a pain to take out?

team_xile · 08-30-2007, 04:58 PM

not really.

WillyW0nka · 08-30-2007, 04:59 PM

alright I'm going to put a critical trigger in it

team_xile · 08-30-2007, 05:01 PM

nice choice sir

WillyW0nka · 08-30-2007, 05:04 PM

there a sticky or anything on it?

team_xile · 08-30-2007, 05:15 PM

no, but you can always check out www.pbreview.com and see what other people thought about it.

WillyW0nka · 08-30-2007, 05:26 PM

About what?

Anyways, which side does the trigger pin come out of, or can it come out of either side?

team_xile · 08-30-2007, 05:28 PM

I believe it is the side with the gauge on it, but don't quote me on that. I will go look quick just to make sure, gimme a second.

WillyW0nka · 08-30-2007, 05:30 PM

but the gauge can go on either side of the gun...

team_xile · 08-30-2007, 05:30 PM

looking at the nerve, it doesn't look like you have to have it a certain way, but I removed it from the side w/ the gauge on it.

EDIT:

Yes, however stock, the nerves regulator is on the right side of the marker. (right as in if you were holding it like you were shooting)

WillyW0nka · 08-30-2007, 05:32 PM

ok so you pushed it out the right side?

team_xile · 08-30-2007, 05:33 PM

yes. However, as I said. After looking at it, it doesn't seem like it really matters.

WillyW0nka · 08-30-2007, 07:33 PM

wow, this POS is really pissing me off. Ok, so the critical trigger wouldn't even fit inside the frame so I put the stock back in. Then upon reconnecting the wire that connects the lower board to the upper board, the recieving piece on the lower board snaps right off the god damned board. SO, my question now, could I just buy a lower shocker board? Or a blackheart board?

team_xile · 08-30-2007, 07:45 PM

sorry to hear that man. You gotta be careful when disassembling the nerve. Everything is way to compact in there. There isn't much room for error.

ANYWAY:
Yes you can buy a shocker board for the nerve. I do not recommend the blackheart board though. Just for the fact that it is capped at 20 bps, and the nerve can shoot over 24. Sure you have more modes, but it is making your nerve slower.

usafpilot90 · 08-30-2007, 07:49 PM

I think you have to file down the insides of the trigger frame, I remember seeing the installation video for the ION Critical trigger and he spent quite some time using a file on the insides. And you definitely don't want to downgrade your board, they replaced Shocker boards with Nerve boards for a reason. Blackhearts are a waste of money when you could spend $30-$40 for a much better board. You should really look into a Russian Legion Virtue board, I would buy that board for the training mode alone.