[triple g paintballer]

tell me wat u think

MATERIALS--- dremel with all fileing attachments
sand paper
cloth
and really good eye sight





FIRST---find how far the tube goes into ur feed neck and mark it off from the top of the tube down
l l [ ]
l____l [_ _]
l l \ /
\ / l l

now cut on the line u marked right acrose once u are down with that take the black stopper off itll be hard but it will come off. After that file down the end where u just cut off the peace of tube with the sand paper when u have done that u need to change the attachment on the dremel to sand the tip around to make the slope so itll slide in easier and thats it GOOD LUCK

http://i96.photobucket.com/albums/l1...r/DSCN2493.jpg

http://i96.photobucket.com/albums/l1...r/DSCN2496.jpg

http://i96.photobucket.com/albums/l1...r/DSCN2498.jpg

http://i96.photobucket.com/albums/l1...r/DSCN2500.jpg

[XxAltecxX]

I found a hack-saw, and pipe cutter to work best. Take the pipe cutter and make a mark all the way around the feedneck, then cutting it with the hack saw, using the mark as a guide.

BTW- Take the loader APART before cutting the feedneck!

[triple g paintballer]

haha yeah i have already done it those where my pics but yeah i would amagian that a hack saw would work pretty good and i left with together it was a lot easier to hold with it all together

[Conor1148]

i'm sorry, i'm more of a empire b kinda guy so i'm not very familiar with velocitys, so what did you do? i'm assuming you cut that rubber stupp off where the feedneck touches the loader?

[xbattlecreekballerx]

i see the problem......its on an ion. j/k. but yeah

sanding down hoppers is a *****. when i first got a halo i had to sand it for a million hours to fit it in my feedneck.

[triple g paintballer]

Originally Posted by Conor1148

i'm sorry, i'm more of a empire b kinda guy so i'm not very familiar with velocitys, so what did you do? i'm assuming you cut that rubber stupp off where the feedneck touches the loader?

well when u get it and put it on it sticks up about half an inch or so and i cut it all down so its not nearly as tall and all

[triple g paintballer]

Originally Posted by xbattlecreekballerx

i see the problem......its on an ion. j/k. but yeah

sanding down hoppers is a *****. when i first got a halo i had to sand it for a million hours to fit it in my feedneck.

naw it fit in the feed but if u look at the pics its sticken out like ****en crazy and just looked kinda wierd bein so tall so i cut it down

[imguessingurgay]

Isnt this common sense?

[triple g paintballer]

it myte be to some people and not to others

[xx2liveist2diexx]

BandSaw FTW took like 2 secs straight cut.

[triple g paintballer]

Originally Posted by xx2liveist2diexx

BandSaw FTW took like 2 secs straight cut.

i would of used somethin like that but i didnt want it to chip and big peices off

[triple g paintballer]

ups

[.adam]

First off you don't up these posts, its the Voided Warranty section, you're not selling your idea. Second off, a hacksaw or bandsaw takes one minute and then finish with 100-200 grain sandpaper.

[triple g paintballer]

and a third of ---------kiss my ***

[oddwala]

try taking out the o-ring in ur ion feedneck it make it more flush with the hopper

[triple g paintballer]

yeah i already have 1 out but it dosent make any difference with bein flush since the orings are on the side of the feed neck