Racegun parts

Metability · 12-06-2012, 04:53 AM

Hi everyone, i'm new here and was referred by someone on another website. So I have had this Race Gun sitting around for about 4 years. I bought it in the current condition and I was wondering what it would take to get the parts to make it fully functional again.

The wires from the 3-way are cut and do not have the board connector on them. Also, the button pad for the back needs to be replaced as it is in poor condition. There is also no charger or anything for it. I tried looking for parts online, but I kept coming up with dead ends. If anyone can help me get this up and firing I would be eternally grateful. Thanks!!

Lucas

Darkapollo · 12-06-2012, 08:13 AM

Hi!
Check ANSGear.com for parts. I have a few but they should have the button pad and 3way wire.

Darkapollo · 12-06-2012, 09:46 AM

Ok.. Now that I have a few minutes to answer the question fully..
ANS gear has the last of the 'new' racegun parts. I wouldnt buy a new battery from them, but the rest of the parts are good.
You could also send it to someone who specializes in raceguns for a tweek-n-tune.

I would hate to refer you to ANOTHER site, but customcockers.com is where you will find the most support. Granted, itll mostly be from me and a small group of others.

Nickdennis · 12-06-2012, 09:55 AM

http://www.ansgear.com/Autococker_E_...Sale_s/109.htm

Nickdennis · 12-06-2012, 09:55 AM

This is what the guy above is talking about.

sandflea_97 · 12-06-2012, 10:38 AM

I saw you on Reddit, OP. Good luck getting this thing shooting, you don't see too many Raceguns left.

Team_ILLNatured · 12-06-2012, 11:26 AM

Quote:

Originally Posted by sandflea_97

I saw you on Reddit, OP. Good luck getting this thing shooting, you don't see too many Raceguns left.

yes, and i have 2 operational

Quote:

Originally Posted by Darkapollo

Ok.. Now that I have a few minutes to answer the question fully..
ANS gear has the last of the 'new' racegun parts. I wouldnt buy a new battery from them, but the rest of the parts are good.
You could also send it to someone who specializes in raceguns for a tweek-n-tune.

I would hate to refer you to ANOTHER site, but customcockers.com is where you will find the most support. Granted, itll mostly be from me and a small group of others.

DarkApollo knows his stuff. he restored my Dark Freeflow race to NIB condition, like when i bought it in 2003(ish) and his prices are EXTREMELY reasonable

and now it's Sexytime:

(btw, that is DarkApollo's Table/floor)

Darkapollo · 12-06-2012, 12:08 PM

^^Opie is working on a discount for next time with all the business he sends my way.

Team_ILLNatured · 12-06-2012, 12:13 PM

hahaha. did my buddy from Rochester get his freeflow off to ya?

Darkapollo · 12-06-2012, 02:50 PM

I dont believe so.. At least I dont recall sending anything to Rochester..

Team_ILLNatured · 12-06-2012, 02:53 PM

alright. well eventually my buddy will be sendin u a silver boxxer

Team_ILLNatured · 12-06-2012, 06:53 PM

alright racegun fans, I got a new camera, and im bored, so IT'S SEXY TIME!:

Darkapollo · 12-06-2012, 07:21 PM

That Orri is sexy..

Team_ILLNatured · 12-06-2012, 07:43 PM

its gonna come your way soon. im ****ing pissed off at it. now it feels like the lug backed out, along with the issue i was havin w/ the eyes

Metability · 12-06-2012, 08:12 PM

Hey everyone I appreciate all the replies! Those Raceguns are the tits! I am going to order a new button pad here in a few minutes. Would it be wise to buy a spare or do they not go bad very often? I know that the battery is newer, as the previous owner just bought a new one every time he lost a charge on it, so it could very well take a charge if I could track that stuff down. It has been so long since I have touched any of my markers and this is the only autococker I have ever had or been around. Also, I have no idea what the air fitting is that I need for the forward handle (Forgot name of that part also, I feel so pathetic!) and the air line for it? I feel that if I get the wiring connector for the 3-way that I can solder the wiring together no problem. Would it be a good decision to get eyes for this marker?

Darkapollo, I tried sending you a message but it wouldn't let me.

Thanks for the help everyone, you are more than kind!

Darkapollo · 12-06-2012, 08:19 PM

Yeah you need 10 posts I think before you can PM.

In all of the times and all of the guns I have worked on, only two have needed new button pads. One was missing the pad itself and the other was missing the actual metal buttons inside the pad.
Order two, but they rarely go bad.
I have a few chargers available too.

You need the macro line fitting for the High Pressure Regulator (front handle) and macro line.

You dont need eyes. Opies Dark FreeFlow is blind and it rips a good clip.

Team_ILLNatured · 12-06-2012, 08:29 PM

5 posts. but close enought

PM me that address again, an i'll let u know when it's on the way

Darkapollo · 12-06-2012, 08:41 PM

Just to toss my two babies up in here..

Metability · 12-06-2012, 08:41 PM

Okay I will just order the one then. The button pad is separated from the button board, and it has corrosion or something all over it. What would you want for a charger? Do you have the PC cable or software that it comes with as well? If you would prefer to email me it is lucas89005@yahoo.com or we can wait until I have a few more posts. Also, what kind of air tank should I be looking at getting?

Absolute.Paintball · 12-06-2012, 08:46 PM

I have a few race gun parts I acquired from a store that went out of business If your interested shoot me a pm and a price.

3 membrane pads aka button pad
3 noid manifolds
3 plastic wire clips
2 ring snaps item # N5000-43
2 retaining rings item # 5133-12
2 o-ring NIT 90sh item # 91417-009-1
2 o-ring NIT 70sh item # 91417-024

Idk if the item number helps much I'm just listing what is on the package.

Team_ILLNatured · 12-06-2012, 08:50 PM

Quote:

Originally Posted by Darkapollo

Just to toss my two babies up in here..

OMG that makes my collection look like junk