Official MARQ Troubleshooting/Known Issues...

ladd_17 · 12-13-2006, 09:11 PM

So.. I'm having lots of issues with blowing balls up in the chamber. I've tried dropping the lpr, and I've switched from a halo to a pulse, none of which seems to work. I know it's not the paint because the same stuff runs through my alias just fine. Any ideas?

LAWSON · 12-13-2006, 09:17 PM

ok, when i have the trigger spring in it is as stiff as a mech cocker. So i cut it, still to hard, cut it again still way to hard, i gave up and took it out cuz there was almost nothing left to cut. i love the trigger pull now but it goes full auto, debounce is on max. What else can i do to make sure it doesnt go full auto, also how many turns in is the lpr set at stock.

thank you

geeZus · 12-13-2006, 09:31 PM

Quote:

Originally Posted by LAWSON

ok, when i have the trigger spring in it is as stiff as a mech cocker. So i cut it, still to hard, cut it again still way to hard, i gave up and took it out cuz there was almost nothing left to cut. i love the trigger pull now but it goes full auto, debounce is on max. What else can i do to make sure it doesnt go full auto, also how many turns in is the lpr set at stock.

thank you

Magnet mod. I had the EXACT same problems. I just magnet modded my trigger and it feels GREAT.

LAWSON · 12-13-2006, 09:35 PM

hey, i am probally the most picky trigger pull person, all of my guns have had atleast 3 hours put into their triggers, i have put more time into my onyx's, are there any setting i could do or anthing else like that

hazel1 · 12-13-2006, 09:53 PM

the absolute best thing to do is a try different magnets

LAWSON · 12-13-2006, 09:56 PM

im trying to stay away from the magnets and spring

96 Ls lnteg · 12-13-2006, 10:13 PM

Quote:

Originally Posted by LAWSON

im trying to stay away from the magnets and spring

than wait for another board.. cause thats prolly the only other way you will get it to stop bouncing.. an Lpr is normally around 60-70psi..

LAWSON · 12-13-2006, 10:24 PM

could lowering the lpr or changing the dwell help?

96 Ls lnteg · 12-13-2006, 10:31 PM

Quote:

Originally Posted by LAWSON

could lowering the lpr or changing the dwell help?

not imo..

LAWSON · 12-13-2006, 10:49 PM

i have cut the spring a lot but it still stays hard!

hopelessandsic · 12-13-2006, 10:59 PM

use a pen spring and try cutting that one.

ladd_17 · 12-13-2006, 11:04 PM

Quote:

Originally Posted by ladd_17

So.. I'm having lots of issues with blowing balls up in the chamber. I've tried dropping the lpr, and I've switched from a halo to a pulse, none of which seems to work. I know it's not the paint because the same stuff runs through my alias just fine. Any ideas?

.

LAWSON · 12-13-2006, 11:33 PM

i used a pen spring and wen i cut it slowly till it could go no further and it was still stiff!

jimy_b · 12-14-2006, 05:09 AM

ladd_17 i had the same problem 4 weeks ago! I just forgot that i could move back or forward the breech. after adjusting this the day was great!

the incubus · 12-14-2006, 10:08 AM

Quote:

Originally Posted by 96 Ls lnteg

than wait for another board.. cause thats prolly the only other way you will get it to stop bouncing.. an Lpr is normally around 60-70psi..

A Techna will help eliminate bounce altogether. I'm just not sure if Jason has produced any as of yet.

96 Ls lnteg · 12-14-2006, 10:30 AM

Quote:

Originally Posted by the incubus

A Techna will help eliminate bounce altogether. I'm just not sure if Jason has produced any as of yet.

I think jason should worry about catchin up with his orders an his terrible customer service before he starts producing other triggers, I know he's a busy man, there is no excuse 2 his lack of customer service

the incubus · 12-14-2006, 10:48 AM

Well MuthaEffinMike... he works on all styles at the same time. He does what he can. Lemme guesss... You're waitin on a Trigger for a while now?

96 Ls lnteg · 12-14-2006, 11:04 AM

Quote:

Originally Posted by the incubus

Well MuthaEffinMike... he works on all styles at the same time. He does what he can. Lemme guesss... You're waitin on a Trigger for a while now?

I am actually not waiting on one

4thDegree · 12-14-2006, 11:05 AM

Sure there is an excuse. He has a full time business that supports his company and the triggers he makes is a sideline business. I am sure that he has balanced the profitability of giving up his other business versus the profitability of making triggers full-time. I believe we all can deduce which he decided was the more beneficial endeavor. Ergo, we wait....

geeZus · 12-14-2006, 12:32 PM

All Mike said is he should catch up on orders and improve his customer service before he goes out and makes new triggers. If he designs a Techna for the Marq series, he's just gonna find himself backup MORE. No where did he say that he had to devote his entire week to making triggers, just catch up on where he's behind before he starts making new ones.

WARHAWK Matt · 12-14-2006, 07:35 PM

I bought my Marg6 last week and had problems with it breaking paint and blowing up paint in the barrel. I used many different barrels same problem. I took my board and flipped my switches to off except for capped and ramping. Now it only breaks paint when it ramps. A slow single pull and it does fine. I'm using a stock Halo with new batteries.