[streetfamesupra]

okay so i got the new impeller in. but it is the one with the prongs that stick up. i think it came from the newer revvy. it drops balls a lot slower. is there something im missing or doing wrong? or is this just the wrong impeller

[flight cancled]

you need a standard 12v revvy impellor. I haven't messed with the newer style impellors, but you might want to try to bend the paddles down so that they are scraping the side of the raceway.

[prem205]

so will the revy impellor feed 15 consistantly?

[flight cancled]

yes, it should do a bit better then that

[KLUG]

What about a single paddle impeller, like on one side not like a revvy one.

[flight cancled]

just one paddle wouldn't be very affective.

[Dylusion]

the pics for the speedfeed dosent work i have been looking for one for long time can you send me pic

[flight cancled]

sent and fixed

[lowrider]

Originally Posted by flight cancled

Three battery mod-

(you need a 9 volt battery connector, superglue or double sided Velcro, and a drill or knife) cut the red wire going between the two boards. connect the red wire coming form the circuit board to the black wire of the connector. Now connect the red of the connector to the red coming from the battery board. Now drill or cut out a hole where the two halves of the ball ramp meets so that the wires can fit in the gap. Now is where you make a decision: Do you want the ball ramp? If not mount the 9v using one of these super glued or velcroed to the bottom of the ball cavity under the door.
Can also be done with the battery conector mod the same way by substisuting the two main connecotrs for the battery board in the diagram.
http://www.stewmac.com/shop/Electron...ting_Clip.html
If you want to keep the ball ramp you can cut out a little strip where the upper corner of the ramp can fit.

i improved this mod.i wired a switch into the circuit so that i can turn the mod on and off.because i burnt up my old motor with this mod. the diagram in the pic tell how to do the mod.in the pic it shows a 3 way slider switch, you can also use a toggle switch.

[flight cancled]

the mod shouldn't burn out the motor, what is more likely is that the gears were out of alingment.

[lowrider]

they may have been,but i was a little weary because that was the only mod that i had done.so after i got another motor i installed the switch into the seires(sp).

[PaintballAtack]

to Lazy to read each page, easy way to save the door life is to sand or dremal the inside of the door so the whole inside is even.
(did that mod with the battery mod)

[KansasFish]

what if i whired my board up like this. Will it hurt anything?

[flight cancled]

by putting the batteries in parralel, you will not get enough voltage for the servo to run.

[KansasFish]

it works fine for me and it will even run off a single 9v

[flight cancled]

there is no scientific way that the speed is the same with 1 9v supplying ~6 volts to the servo vs. 2 9vs giving ~12

[KansasFish]

so is it ok to have the way i have them or should i change them to the way its shown. Will it speed up if i change it?

thank you

[flight cancled]

it will most deffinately speed up if you put it the way its shown.

[prem205]

is the new revy impellor the 12volt 4 blade one?
http://store.paintballace.com/vireim.html

[flight cancled]

the ones out of the acutally revies work, it seems that the ones from the tripod are shaped diferently to fit inside of the different shell tops.

[prem205]

so the one i posted doesnt work??

what about the one in viewloaderparts?
http://www.viewloaderparts.com/index...&categoryID=88