[iamthanos]

Hey guys i am looking to do a stock class project on an autococker. Can anyone help me out by linking me the parts i will need. Stock class feed and drop out changer. any help would be appreiciated

[painter4life05]

CCI makes the best drop out changer, as for feed you can mod an autococker to use a phantom stock class feed.

[iamthanos]

will the cci drop out fit in the autococker vertical asa?

[painter4life05]

No it will not my mistake, you need this
http://paintballgateway.com/ccistcl12grq.html

[eudaman]

Originally Posted by iamthanos

will the cci drop out fit in the autococker vertical asa?

Yes it will, but make sure you know its more involved than just adding parts

[EvilAuthorityX]

Originally Posted by eudaman

Yes it will, but make sure you know its more involved than just adding parts

A cci drop out will not fit a cocker asa

[eudaman]

whoops i was thinking quick change thanks for the correction!

[iamthanos]

what else i need to add? for drop changer

[kpmurphy]

Palmer's makes a feed tube that goes on a 7/8 feedneck. Sanchez too I think. Someone makes one that fits in a normal vertical feed

[painter4life05]

A drop out changer just screws right into the vert asa just like a normal regulator.

[iamthanos]

do i need a special valvue to use the unregulated co2 in the cocker?

[painter4life05]

It is best to run your co2 regged, palmsers makes a drop out with a reg built in, but its a bit pricey, imo its worth it though

[iamthanos]

Originally Posted by painter4life05

It is best to run your co2 regged, palmsers makes a drop out with a reg built in, but its a bit pricey, imo its worth it though

i cant find it on there website. do you have a link for it?

[masterofTHUMBS]

I haven't seen a quick change with a reg before but you can get away without using a reg if you use red springs for the valve and hammer.

[painter4life05]

i fail

[EvilAuthorityX]

Originally Posted by painter4life05

http://palmer-pursuit.com/cart/index...oducts_id=1222

That's not a drop out

[painter4life05]

I apologize I have failed this thread

[pumpmonkey1]

I have a superbolt, so I used a pvc pipe. If you have a threaded feedneck, you can do the same. Here is the link to my post:

https://www.pbnation.com/showthread.php?t=3708844

That will give you all the info you should need to build one for under $3.

If you do not have a threaded feedneck, you will need one of these:

http://www.paintballgateway.com/smloaders.html

or one of these if you have a side feed cocker:

http://www.paintballgateway.com/papulo.html

Those are pretty much all of your options at the moment.

Also, I am currently using a Palmers Pursuit T-stock (straight) and lovin' it.

Here is the link:

http://www.paintballgateway.com/stocks.html


PM me if you have any questions about the homemade feed tube.

[iamthanos]

Originally Posted by painter4life05

I apologize I have failed this thread

lol its all good man i aprieciate the help. So you think as long as i use my red springs out of my maddman kit i should be be good using un regulated co2? its a pump so there arent any pnues to mess up i would just have to keep up on my o rings.

[painter4life05]

Time for me to post something correct and relevant. I have the sanchez feed adapter posted above and it works great on stock press fit feedneck.

[iamthanos]

sweet thats the one i was going to get. But i milled my feedneck and put the cp ego 11 feed neck on there