Find fields & stores near you!
Find fields and stores
Zipcode
PbNation News
PbNation News
Community Focus
Community Focus

Reply
 
Thread Tools
Old 02-13-2014, 08:02 PM #1
Ken448
Meow
 
Ken448's Avatar
 
Join Date: Dec 2002
Location: SE Michigan
Ken448 is a Supporting Member
 has been a member for 10 years
Ken448 posts videos on PbNation
Ken448 supports Empire
Zero B / Psycho Ballistics Chopping suggestions?

Settings are as follows:
TT Band 75%
TT TOL 12%
Release 4mS
Pull 1mS
Empty 2mS


SON 4.0mS
C OFF 28mS
C T/OUT 1.0s
C ON 65mS
C DELAY 6.0mS

Anyone have any suggestions? Doesnt matter how fast or slow I shoot it, eyes on/off and theres no blowback to speak of (2nd ball drops right into chamber)


Last edited by Ken448 : 02-13-2014 at 08:09 PM.
Ken448 is offline   Reply With Quote
Old Sponsored Links Remove Advertisement
Advertisement
Old 02-13-2014, 09:58 PM #2
jim4130
proud gmax owner!!!
 
jim4130's Avatar
 
Join Date: Jul 2008
Location: woburn MA.
jim4130 plays in the PSP
jim4130 plays in the APPA D4 division
jim4130 is one of the top 250 posters on PbNation
jim4130 is Boss
Well if the balls are dropping right in its not chopping. What are using for paint and is it bored corectly or is that eigenbarrel to tight? What about your detent? Have you chevked its functioning properly?
__________________
OBE
SBPB

come check out my gun collection

proud suporter of

shocker owners
jim4130 is offline   Reply With Quote
Old 02-13-2014, 10:02 PM #3
Ken448
Meow
 
Ken448's Avatar
 
Join Date: Dec 2002
Location: SE Michigan
Ken448 is a Supporting Member
 has been a member for 10 years
Ken448 posts videos on PbNation
Ken448 supports Empire
Breech and bolt is loaded with paint

Itll shoot 4 to 5 balls fine, then soup. then another few. Barrel doesnt matter (Ive got both sizes eigen and normally dont use the smaller on a cocker), paint doesnt matter. I honestly think the bolt is closing too quick. Hopper (no matter what I use) is clean so its not blowing back. Detent FEELS fine and theres no sharps in the breech. Cocks fine on classic etc. This is why Im confused!
Ken448 is offline   Reply With Quote
Old 02-13-2014, 10:05 PM #4
jim4130
proud gmax owner!!!
 
jim4130's Avatar
 
Join Date: Jul 2008
Location: woburn MA.
jim4130 plays in the PSP
jim4130 plays in the APPA D4 division
jim4130 is one of the top 250 posters on PbNation
jim4130 is Boss
How old is the paint?
__________________
OBE
SBPB

come check out my gun collection

proud suporter of

shocker owners
jim4130 is offline   Reply With Quote
Old 02-13-2014, 11:38 PM #5
Eshik
 
 
Eshik's Avatar
 
Join Date: Oct 2009
Location: Houston
Annual Supporting Member
Eshik has achieved Level 1 in PbNation Pursuit
Eshik has achieved Level 2 in PbNation Pursuit
Are you getting paint up the neck into the hopper or just in the barrel?
Eshik is offline   Reply With Quote
Old 02-13-2014, 11:41 PM #6
Ken448
Meow
 
Ken448's Avatar
 
Join Date: Dec 2002
Location: SE Michigan
Ken448 is a Supporting Member
 has been a member for 10 years
Ken448 posts videos on PbNation
Ken448 supports Empire
bolt and breech, then of course barrel

Mechanics are fine, What Im concerned about is are the settings good, or is something strange?
Ken448 is offline   Reply With Quote
Old 02-14-2014, 02:18 AM #7
Eshik
 
 
Eshik's Avatar
 
Join Date: Oct 2009
Location: Houston
Annual Supporting Member
Eshik has achieved Level 1 in PbNation Pursuit
Eshik has achieved Level 2 in PbNation Pursuit
Chopping in a Cocker is caused by a bolt closing to soon and slicing the ball in half. This will cause paint, she'll, and all kinds of nastiness to be left in the feed neck and up into the hopper. This would most likely be caused by bad settings, a LPR set to low or going bad, or pump arm \ back block not set right.

If the paint is contained in the breach the ball is feeding correctly and breaking somewhere later in the process. Your settings would be correct and you need to look for another reason. Check for clean detents, no sharp protrusions on the face of the bolt or detents. Try a different kind of paint and a different barrel.

This is not definitive, just my experience from owning and working on my Cockers for many years. I have been known to be wrong more than once.
Eshik is offline   Reply With Quote
Old 02-15-2014, 09:57 PM #8
Ken448
Meow
 
Ken448's Avatar
 
Join Date: Dec 2002
Location: SE Michigan
Ken448 is a Supporting Member
 has been a member for 10 years
Ken448 posts videos on PbNation
Ken448 supports Empire
mmkay, after going over the gun front to back once again, all mechanics are fine, but I did enlarge the eye hole on the inside a bit. The design inside there is a lip, and the eye is right at the bottom of that. Runs fine now
Ken448 is offline   Reply With Quote
Reply


Thread Tools

Posting Rules
Forum Jump