[Captainhammertime]

Should have this in on Friday or Saturday, can't wait to blast some faces with it!

[Joe13750]

Just put another case through my vapor tonight (only about 4 cases now) and its getting better and better every week. I finally think I got my settings right.
My friend just picked up a luxe 2.0 and chrono'd the same, my vapor was hands down smoother and quieter. That is with my setup being much lighter as well (ninja 45/45 and spire vs his empire 68/45 and rotor).

My one gripe I have is barrel breaks. It's never a chop just barrel breaks.
Current settings : 12 dwell, 3/4 turn out on ft screw, 35 on bolt return and 10 on breech delay. I am using pooty bolt with all buna70 orings. I tried clipping off a few coils on the detents and even kept them very slightly lubed. As for barrel I am using a .685 bob long one piece and paint is bored out about .679. I also have the v3 can installed.
Any suggestions on what I can try to eliminate barrel breaks? Thanks in advance

[Vissa]

I also still have barrelbreaks, almost every game some. Pretty annoying, really has to do something with the Vapor. My teammates GEO 3 shoots every freakin paint it gets.

My Vapor is set up at 14 dwell, 40 Bolt return, 12 breach delay, FT 1 turn out. Maybe it's spiking or something, that it hits the ball so hard sometimes it cracks and burst in the barrel? Don't know.

I got the V2 parts still, waiting on the V3.

[Screaming4vengence]

Originally Posted by Joe13750

Just put another case through my vapor tonight (only about 4 cases now) and its getting better and better every week. I finally think I got my settings right.
My friend just picked up a luxe 2.0 and chrono'd the same, my vapor was hands down smoother and quieter. That is with my setup being much lighter as well (ninja 45/45 and spire vs his empire 68/45 and rotor).

My one gripe I have is barrel breaks. It's never a chop just barrel breaks.
Current settings : 12 dwell, 3/4 turn out on ft screw, 35 on bolt return and 10 on breech delay. I am using pooty bolt with all buna70 orings. I tried clipping off a few coils on the detents and even kept them very slightly lubed. As for barrel I am using a .685 bob long one piece and paint is bored out about .679. I also have the v3 can installed.
Any suggestions on what I can try to eliminate barrel breaks? Thanks in advance

Bore your paint to your barrel better it may just be the overbore breaking the paint. And also...use the barrel that came with the gun its great.

[Joe13750]

Originally Posted by Screaming4vengence

Bore your paint to your barrel better it may just be the overbore breaking the paint. And also...use the barrel that came with the gun its great.

I have tried every bore size without any luck, the tighter seems to be much worse. With the .685 I have much better luck.

[Joe13750]

Originally Posted by Vissa

Maybe it's spiking or something

This might be? Sometimes I chrono I will be sittomg at around 270 and o woll get a random nall at like 320+
.. maybe reg needs to be broken in more? When I picked up a new clone vx I had a problem with the reg spiking nut it went away after like three tanks dry fired through it

[Gaaron_Blanch]

just picked up a vapor in a trade for my ego 11. he was complaining it chopped and was ****ty. i took it, cleaned it and havent even tuned it yet, and its one of the smoothest shooting guns ive ever shot. ive only put about a hopper and a pod out since i got it an hour ago, but its hands down my favorite gun ive owned. cant wait to tune it!

[Screaming4vengence]

Originally Posted by Joe13750

This might be? Sometimes I chrono I will be sittomg at around 270 and o woll get a random nall at like 320+
.. maybe reg needs to be broken in more? When I picked up a new clone vx I had a problem with the reg spiking nut it went away after like three tanks dry fired through it

Sounds like reg or noid then. Still waiting on reverend promod to chime in.

[Joe13750]

just recent update, i have been putting a lot more paint through the gun and it seems like breaking it in is helping. The spiking shot is gone over the chrono(actually pretty consistent) but last night i did still get some barrel breaks, only about like 2-3 though for a case of paint which i suspect isn't bad or just normal?

[ProMod]

Originally Posted by Screaming4vengence

Sounds like reg or noid then. Still waiting on reverend promod to chime in.

reg rebuild, fresh battery, slightly higher dwell.

sorry for the late chime-in, I've been super busy. Post in the Vapor Vendetta Thread for faster responses.

[joffre7392]

If I emailed machine with no response about the v3 parts do I just email them again?

[PaintballACE28]

How do u mess with the microswitch on the vapor

[ProMod]

Originally Posted by PaintballACE28

How do u mess with the microswitch on the vapor

... you don't ?

what are you trying to do?


- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

In other news, this is straight off the Vapor Vendetta facebook group (and now on Machine's main page)

"Small teaser of the new diffraction limited photon etching multi color processing soon to be available from Machine."



(yes, that's a color-photo...black and grey)


"Here's a different color combo of the new etched multi-color process."

[LuLuTheMonk]

Originally Posted by joffre7392

If I emailed machine with no response about the v3 parts do I just email them again?

Same question here.

[ProMod]

the first two waves of V3 parts went out already (from my last email-conversation with the techs)

Shoot them another email and ask for an ETA (or ask them to confirm that you're on the list)

[ice1124]

Originally Posted by PbN_AutoTrader

Nice!
These guns shoot great
friend has 53+ cases so far and not a break! *knock on wood*

I'm at 72 cases now and have not chopped a ball in the breach. But I have broke a ball in the barrel but after 2 or 3 shot it was shooting straight again.

[PbN_AutoTrader]

Vapor is the best marker on the market hands down.

[Kyle Wilson59]

How long does it take for a vapor to break in? Got a brand new one so I was wondering

[ProMod]

There's only 1 spring (the hpr spring) that really needs to get settled. After about 2-3 cases you should be good.

[Kyle Wilson59]

Originally Posted by ProMod

There's only 1 spring (the hpr spring) that really needs to get settled. After about 2-3 cases you should be good.

Alright thanks

[Kyle Wilson59]

Another ? Where do I go to register it or whatever?