[Shootingropes]

I always hated some of the features on the original geo. No room between the reg and trigger guard, those ugly "rail esc" humps on top, and the wierd flow of lines and curves the gun featured. So if you're looking for a why the project came to be, that would be it.

I knew upon getting this gun that it was going to be a project for me. I don;t have a CNC Mill or a lathe, just a file, dremel, and some sand paper. I'm no where close to being a profesional, but would like to get better at this as I go along.

Let me know what you think so far. If you have any questions, ask, and advice/CC is highly appreciated! I haven't polished the milled area's yet, since I will have to do the whole gun once I get some Lye.

Also PM me if you're an anodizer and would like to take it in as a project/courtesy job Although that's unlikely, I do have money to get it anno'd, but sincerely don't wish to spend more then 100.

[stealthninja]

Looking nice so far, subscrbed for future viewing pleasure.

[Apollo918]

im enjoying this. it looks great.

[FallenHero_08]

Looks Awesome so far, just remember to not cut too much, leave some material left for the sanding steps. looks like your doing just fine so far though.

[theblindchicken]

Diggin it! Looks good. Sub'd for updates!

[lcullum]

this will look so sexy , I was thinking of doing the same

[smokefools66]

I like where you're going with this. The trigger frame looks a lot better and the body looks nice so far. I'm thinking of maybe doing something with my spare 05 body that's been laying around but I've never done any custom work. I'd probably only have access to a file sand paper and possibly my dads Dremel.

[Shootingropes]

Thanks for the support guys. I need to find a direction to go with making the body look real good. Can't be too extravagent though, becaus both sides I want to match.. Ideally.

[jonotwist]

carve perpendicular indents on the milled folds,

but do keep sanding. more.

[KryptonicsPB]

Originally Posted by Shootingropes

Thanks for the support guys. I need to find a direction to go with making the body look real good. Can't be too extravagent though, becaus both sides I want to match.. Ideally.

Careful around the reg area that looks pretty thin.

Looks cool though fur sure

[Shooter28]

Poor mans sl91

[PBFR33K187]

Sick

[andyschein]

felt this in my hands and the space makes the geo feel really comfortable

[DanR]

you should counter sink the front frame screw if its possible my geo 2 had enough extra material there to make it possible

[Shootingropes]

Originally Posted by DanR

you should counter sink the front frame screw if its possible my geo 2 had enough extra material there to make it possible

I was thinking about it, but I might have shaved off too much to make more room for my thumb (I like a wider space).

[big,bad,PAINTBALLER]

Heyyy you made a geo 2!

[stl letta]

Can't wait to see updates

[Shootingropes]

Originally Posted by big,bad,PAINTBALLER

Heyyy you made a geo 2!

Looks nothing like one.

[aresfiend]

Originally Posted by Shootingropes

Looks nothing like one.

Uhh...

Originally Posted by Shootingropes

It's starting to look a LOT more like a Geo2 than a Geo at this point...

[theblindchicken]

Originally Posted by aresfiend

Uhh...

It's starting to look a LOT more like a Geo2 than a Geo at this point...

I'd have to agree that they look similar now, but there are still some major milling differences between the two.


Project's looking good! Keep it up.

[xsvdynastypballa]

Go for gold and cut all the lines off!!...Except that one that goes down the middle.